ZyXEL U-336R User Guide - Page 92

computed by the equation

Get ZyXEL U-336R PDF manuals and user guides View all ZyXEL U-336R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 92 highlights

Command +FNS="string" +FPI="string" +FPR=n +FPS=n +FRQ=pgl,cbl +FSP=n Value n=0 n>0 pgl= 0-64 (HEX value) cbl= 0-FF (HEX value) Description Non-standard byte string parameter. "string": string of hexadecimal coded octets. Local fax station ID string, for polling Rx. Serial port rate control parameter: Automatic DTE rate detection by the DCE. Serial rate is fixed at the value multiplied by 2400 bps. For example, when n=8, the DTE rate is equal to 19200 bps (8x2400). Page transfer status: refer to the +FPTS Class 2 command in previous sections for settings. Receiving quality threshold parameters: Specify the percentage of good lines (e.g. with negotiated number of pixels) required for a page considered acceptable. The percentage of good lines would be computed by the equation: 100 x ( - ) / lc: total line count as reported in the +FPS: response. bl: bad line count as reported in the +FPS: response. If the resulting value is less than the value in , the page is unacceptable. Specify the maximum tolerable number of consecutive bad lines. If this value is exceeded for a given page, the DCE shall consider the page unacceptable. Enable polling command: 78 Fax Operation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
78
Fax Operation
Command
Value
Description
+FNS=
"string"
Non-standard byte string parameter.
"string": string of hexadecimal coded
octets.
+FPI=
"string"
Local fax station ID string, for polling Rx.
+FPR=
n
Serial port rate control parameter:
n=0
Automatic DTE rate detection by the
DCE.
n>0
Serial rate is fixed at the value multiplied
by 2400 bps. For example, when n=8, the
DTE rate is equal to 19200 bps (8x2400).
+FPS=
n
Page transfer status: refer to the +FPTS
Class 2 command in previous sections for
settings.
+FRQ=
pgl,cbl
Receiving quality threshold parameters:
pgl=
0-64
(HEX
value)
Specify the percentage of good lines (e.g.
with negotiated number of pixels) required
for a page considered acceptable. The
percentage of good lines would be
computed by the equation:
100 x (<lc> - <bl>) / <lc>
lc: total line count as reported in the +FPS:
response.
bl: bad line count as reported in the +FPS:
response.
If the resulting value is less than the value
in <pgl>, the page is unacceptable.
cbl=
0-FF
(HEX
value)
Specify the maximum tolerable number of
consecutive bad lines. If this value is
exceeded for a given page, the DCE shall
consider the page unacceptable.
+FSP=
n
Enable polling command: