Acer G330 User Manual - Page 52

To install an easy-swap hard drive, Make sure that the drive is properly inserted before pushing

Get Acer G330 - Altos - 1 GB RAM PDF manuals and user guides
UPC - 750519177044
View all Acer G330 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

34 3 System upgrade 4 Align the new hard disk with the HDD carrier, then secure it with the four screws you removed in step 3-1. 5 Install the new hard drive into the cage. (1) Slide the drive into the cage with the ejector lever still extended. (2) Make sure that the drive is properly inserted before pushing the lever back until it clicks into place. To install an easy-swap hard drive: 1 Remove the side panel from the chassis. Go to page 27 for instructions. 2 Observe steps 2 through 5 of the previous section. 3 Connect the data and power cables to their HDD connectors. 4 Observe the post-installation instructions described on page 26.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
3 System upgrade
34
4
Align the new hard disk with the HDD carrier, then secure it with
the four screws you removed in step 3-1.
5
Install the new hard drive into the cage.
(1)
Slide the drive into the cage with the ejector lever still
extended.
(2)
Make sure that the drive is properly inserted before pushing
the lever back until it clicks into place.
To install an easy-swap hard drive:
1
Remove the side panel from the chassis.
Go to page 27 for instructions.
2
Observe steps 2 through 5 of the previous section.
3
Connect the data and power cables to their HDD connectors.
4
Observe the post-installation instructions described on page 26.