Alcatel OS6855-24 User Guide - Page 129

Booting 6855 Series Switches, Booting an OmniSwitch 6855

Get Alcatel OS6855-24 PDF manuals and user guides View all Alcatel OS6855-24 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 129 highlights

5 Booting 6855 Series Switches For information on booting stand-alone switches and switches in stacked configurations, refer to the sections below. Booting an OmniSwitch 6855 The OmniSwitch 6855 Series switch does not use an on/off switch. The power cord is the switch's only connect/disconnect device. The power connector socket is located on the power supply rear panel. For more information, refer to "OmniSwitch 6855 Series Chassis and Hardware Components" on page 2-1. To boot the switch, plug the power cord (provided) into the power connector socket on the power supply. Next, plug the power cord into an easily-accessible power source, such as a grounded AC outlet or an Uninterruptible Power Supply (UPS). The switch immediately begins the boot process. Allow a few moments for the switch to boot completely, then verify the status of all LEDs on the switch's front panel. A successful boot for a stand-alone switch displays the following LED states: LED States for a Stand-Alone Switch OK Solid green PRI Solid green (Primary), Solid amber (Secondary), Off (Idle) PS1 Solid green PS2 Solid green or OFF if no backup power supply is connected. If any of the LED state differs from the states shown in the table above, refer to page 2-6 for more information. Contact Alcatel-Lucent Customer Support if the LED state persists. For information on logging in and configuring your OmniSwitch 6855 Series switch, refer to the OmniSwitch 6855 Series Getting Started Guide. OmniSwitch 6855 Series Hardware Users Guide September 2011 page 5-1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
OmniSwitch 6855 Series Hardware Users Guide
September 2011
page 5-1
5
Booting 6855 Series
Switches
For information on booting stand-alone switches and switches in stacked configurations, refer to the
sections below.
Booting an OmniSwitch 6855
The OmniSwitch 6855 Series switch does not use an on/off switch. The power cord is the switch’s only
connect/disconnect device. The power connector socket is located on the power supply rear panel. For
more information, refer to
“OmniSwitch 6855 Series Chassis and Hardware Components” on page 2-1
.
To boot the switch, plug the power cord (provided) into the power connector socket on the power supply.
Next, plug the power cord into an easily-accessible power source, such as a grounded AC outlet or an
Uninterruptible Power Supply (UPS).
The switch immediately begins the boot process. Allow a few moments for the switch to boot completely,
then verify the status of all LEDs on the switch’s front panel. A successful boot for a stand-alone switch
displays the following LED states:
If any of the LED state differs from the states shown in the table above, refer to
page 2-6
for more infor-
mation. Contact Alcatel-Lucent Customer Support if the LED state persists.
For information on logging in and configuring your OmniSwitch 6855 Series switch, refer to the
OmniSwitch 6855 Series
Getting Started Guide
.
LED States for a Stand-Alone Switch
OK
Solid green
PRI
Solid green (Primary), Solid amber (Secondary), Off (Idle)
PS1
Solid green
PS2
Solid green or OFF if no backup power supply is connected.