Alcatel OS6855-24 User Guide - Page 70

DC Output Power Cord, Warning., Output Power Terminal Locations

Get Alcatel OS6855-24 PDF manuals and user guides View all Alcatel OS6855-24 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 70 highlights

Installing the PS-I185AC-P (SDR-240-55) Power Supply OmniSwitch 6855 Series Chassis and Hardware Components DC Output Power Cord Warning. Do not insert the NEMA 5-15 plug or IEC 60320 C15 power connector into the system power supply or any live power source until prompted to do so. Failure to follow these instructions may result in bodily injury and/or equipment damage. Before installing the PoE power supply in the chassis power supply tray, be sure to properly install these power cords by following the steps below. 1 To install the output power cord, begin by inserting the BLACK wire into either of the V- terminals located at the top-front of the PoE power supply. 2 Next, insert the WHITE wire into either of the V+ terminals. 3 Using a screwdriver torque each terminal to 7 inch-pounds. 4 Secure the remaining ground wire to the power supply using the supplied attachment screw. Insert the screw through the ground wire connector and tighten firmly. VV+ Top-Front of Power Supply Output Power Terminal Locations page 2-48 OmniSwitch 6855 Series Hardware Users Guide September 2011

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
Installing the PS-I185AC-P (SDR-240-55) Power Supply
OmniSwitch 6855 Series Chassis and Hardware Components
page 2-48
OmniSwitch 6855 Series Hardware Users Guide
September 2011
DC Output Power Cord
Warning.
Do not insert the NEMA 5-15 plug or IEC 60320 C15 power connector into the system power
supply or any live power source until prompted to do so. Failure to follow these instructions may result in
bodily injury and/or equipment damage.
Before installing the PoE power supply in the chassis power supply tray, be sure to properly install these
power cords by following the steps below.
1
To install the output power cord, begin by inserting the BLACK wire into either of the V- terminals
located at the top-front of the PoE power supply.
2
Next, insert the WHITE wire into either of the V+ terminals.
3
Using a screwdriver torque each terminal to 7 inch-pounds.
4
Secure the remaining ground wire to the power supply using the supplied attachment screw. Insert the
screw through the ground wire connector and tighten firmly.
Output Power Terminal Locations
Top-Front of Power Supply
V+
V-