Brother International BAS-416A Instruction Manual - English - Page 17

turning, power, machine, following, displayed

Get Brother International BAS-416A PDF manuals and user guides View all Brother International BAS-416A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

3-2. When turning on the power of the machine 1. If the following are displayed N Case PO5. Error Set NC in order C 0 0 The machine will beep intermittently, and the message will appear as shown on the left. This message means that the needle bar case is not aligned with the needle hole of the needle plate. The machine cannot operate under this condition. 1. First of all, check that the needle bar stop position is correct. When the cam plate 61 is in its upper position, the machine is in the automatic jump condition. This is the normal position. • BAS-416A 0 • BES-1210AC 2. Turn the shaft © slowly. If it is unusually hard to turn or does not turn, the needle thread take-up 0 or the needle bar is not in the proper position. Check again and adjust it. NOTE: Do not turn the shaft forcefully. ' CAUTION MOVING! I Cress START key START 3. When the needle bar case comes to the proper position (in the middle of the undetected area where the needle bar case does not move although the shaft is turned), the buzzer sounds 'beep' and the messages, "CAUTION MOVING!" and "Press START key" are displayed alternately. 4. Press the key. BAS-416A BES-1210AC 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
3-2.
When
turning
on
the
power
of
the
machine
1.
If
the
following
are
displayed
N
Case
PO5.
Error
Set
NC
in
order
C
•
BAS
-416A
0
•
BES-1210AC
0
0
'
CAUTION
MOVING!
I
Cress
START
key
START
The
machine
will
beep
intermittently,
and
the
message
will
appear
as
shown
on
the
left.
This
message
means
that
the
needle
bar
case
is
not
aligned
with
the
needle
hole
of
the
needle
plate.
The
machine
cannot
operate
under
this
condition.
1.
First
of
all,
check
that
the
needle
bar
stop
position
is
correct.
When
the
cam
plate
61
is
in
its
upper
position,
the
machine
is
in
the
automatic
jump
condition.
This
is
the
normal
position.
2.
Turn
the
shaft
©
slowly.
If
it
is
unusually
hard
to
turn
or
does
not
turn,
the
needle
thread
take-up
0
or
the
needle
bar
is
not
in
the
proper
position.
Check
again
and
adjust
it.
NOTE:
Do
not
turn
the
shaft
forcefully.
3.
When
the
needle
bar
case
comes
to
the
proper
position
(in
the
middle
of
the
undetected
area
where
the
needle
bar
case
does
not
move
although
the
shaft
is
turned),
the
buzzer
sounds
'beep'
and
the
messages,
"CAUTION
MOVING!"
and
"Press
START
key"
are
displayed
alternately.
4.
Press
the
<START>
key.
BAS
-416A
BES-1210AC
7