D-Link DSL-2740B User Manual - Page 68

Routing Setup

Get D-Link DSL-2740B PDF manuals and user guides View all D-Link DSL-2740B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 68 highlights

Section 3 - Configuration ROUTING SETUP Enter the destination network address, subnet mask, gateway AND/OR available WAN interface then click "Apply" to add the entry to the routing table. A maximum 32 entries can be configured Allows you to configure RIP (Routing Information Protocol). To activate RIP for the device, select the 'Enabled' radio button for Global RIP Mode. To configure an individual interface, select the desired RIP version and operation, followed by placing a check in the 'Enabled' checkbox for the interface. Click the 'Apply' button to save the configuration, and to start or stop RIP based on the Global RIP mode selected. ROUTING -- STATIC ROUTE Please click the Add or Edit button to set a static routing policy in the list. Please type the Destination Network Address and Subnet Mask. Please select to type the Gateway IP or the interface to be the routing interface. Click the Apply the button to save the configuration. ROUTING -- RIP CONFIGURATION Please choose the Version and Operation, and then decide to Enable or not. D-Link DSL-2740B User Manual 68

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
Section 3 - Configuration
D-Link DSL-2740B User Manual
68
ROUTING SETUP
Enter the destination network address, subnet mask, gateway AND/OR available WAN interface then click "Apply" to add the entry to the routing
table.
A maximum 32 entries can be configured
Allows you to configure RIP (Routing Information Protocol). To activate RIP for the device, select the
'Enabled' radio button for Global RIP Mode. To configure an individual interface, select the desired RIP version and operation, followed by placing a
check in the 'Enabled' checkbox for the interface. Click the 'Apply' button to save the configuration, and to start or stop RIP based on the Global RIP
mode selected.
ROUTING -- STATIC ROUTE
Please click the
Add
or
Edit
button to set a static routing policy in
the list.
Please type the
Destination Network Address
and
Subnet
Mask.
Please select to type the
Gateway IP
or the
interface
to be
the routing interface.
Click the Apply the button to save the configuration.
ROUTING -- RIP CONFIGURATION
Please choose the
Version
and
Operation
, and then decide to
Enable
or not.