Dell Dimension 2300C Dell Dimension 2300C Owner's Manual - Page 92

Clearing Forgotten Passwords

Get Dell Dimension 2300C PDF manuals and user guides View all Dell Dimension 2300C manuals
Add to My Manuals
Save this manual to your list of manuals

Page 92 highlights

www.jp.dell.com | support.jp.dell.com 92 Appendix Clearing Forgotten Passwords CAUTION: Before you begin any of the procedures in this section, follow the safety instructions on page 7. If you forget your user or setup password, you cannot operate your computer or change settings in the system setup program until you clear the forgotten password(s). NOTICE: This process erases both the system and setup passwords. 1 Shut down the computer (see page 31). 2 Turn off any attached devices and disconnect them from their electrical outlets. NOTICE: To disconnect a network cable, first unplug the cable from your computer and then unplug it from the network wall jack. 3 Disconnect the computer power cable from the wall outlet, and then press the power button to ground the system board. 4 Remove the computer stand (see page 19). 5 Open the computer cover (see page 74). 6 Locate jumper PSWD on the system board (see page 77) and remove the jumper plug. 7 Close the computer cover (see page 84), plug your computer into an electrical outlet, and turn on the computer. The existing password(s) will be erased. 8 Shut down the computer (see page 31). NOTICE: To disconnect a network cable, first unplug the cable from your computer and then unplug it from the network wall jack. 9 Turn off any attached devices and disconnect them from their electrical outlets. 10 Disconnect the computer power cable from the wall outlet, and then press the power button to ground the system board. 11 Open the computer cover (see page 74). 12 Reconnect the jumper plug to jumper PSWD (see page 77). 13 Close the computer cover (see page 84).

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
92
Appendix
www.jp.dell.com | support.jp.dell.com
Clearing Forgotten Passwords
CAUTION: Before you begin any of the procedures in this section,
follow the safety instructions on page 7.
If you forget your user or setup password, you cannot operate your computer
or change settings in the system setup program until you clear the forgotten
password(s).
NOTICE:
This process erases both the system and setup passwords.
1
Shut down the computer (see page 31).
2
Turn off any attached devices and disconnect them from their
electrical outlets.
NOTICE:
To disconnect a network cable, first unplug the cable from your
computer and then unplug it from the network wall jack.
3
Disconnect the computer power cable from the wall outlet, and then
press the power button to ground the system board.
4
Remove the computer stand (see page 19).
5
Open the computer cover (see page 74).
6
Locate jumper PSWD on the system board (see page 77) and remove
the jumper plug.
7
Close the computer cover (see page 84), plug your computer into an
electrical outlet, and turn on the computer.
The existing password(s) will be erased.
8
Shut down the computer (see page 31).
NOTICE:
To disconnect a network cable, first unplug the cable from your
computer and then unplug it from the network wall jack.
9
Turn off any attached devices and disconnect them from their
electrical outlets.
10
Disconnect the computer power cable from the wall outlet, and then
press the power button to ground the system board.
11
Open the computer cover (see page 74).
12
Reconnect the jumper plug to jumper PSWD (see page 77).
13
Close the computer cover (see page 84).