Dell PowerEdge M420 8/4 Gbps FC SAN Module Administrator's Guide - Page 66

portCfgShow, Understanding Virtual Fabric restrictions, Understanding, Admin Domain restrictions

Get Dell PowerEdge M420 PDF manuals and user guides View all Dell PowerEdge M420 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 66 highlights

B portCfgShow Note Operands Examples The execution of this command is subject to Virtual Fabric or Admin Domain restrictions that may be in place. Refer to "Understanding Virtual Fabric restrictions" on page 32 snf "Understanding Admin Domain restrictions" on page 33 for details. This command has the following operand: license Specifies the license key to be installed. This operand is required. To add a license key to the switch: switch:admin> licenseadd DXXtN3LmRSMWCSW3XmfSBPfrWKLZ3HMTN73rP9GANJMA adding license-key [DXXtN3LmRSMWCSW3XmfSBPfrWKLZ3HMTN73rP9GANJMA] portCfgShow Synopsis Description Displays port configuration settings. portcfgshow portcfgshow [slot/]port portcfgshow option [slot/] [arguments] [optional_arguments] Use this command to display the current configuration of a port. The behavior of this command is platform-specific; output varies depending on port type and platform, and not all options are supported on all platforms. "Non-GbE port displays" on page 52 If no operand is specified, this command displays port configuration settings for all ports on a switch, except Gigabit Ethernet (GbE) ports. Non-GbE port displays The following information is displayed when the command is issued for all ports or for a specific port: Area Number Displays the port area number. This field is displayed only when portCfgShow is executed for a specific port. Speed Displays Auto for auto speed negotiation mode, or a specific speed of 1, 2, 4, or 8 Gbps. This value is set by the portCfgSpeed command. Fill Word Displays 0(Idle-Idle) or 1(arbff-arbff). This parameter is set by the portcfgFillword command. AL_PA Offset 13 Displays (...) or OFF when the arbitrated loop physical address (AL_PA) on the port is configured to use a 0x0 AL_PA address (default). Displays ON when the address configuration is 0x13 AL_PA. This value is set by the portCfgAlpa command. Trunk Port Displays ON when port is set for trunking. Displays (..) or OFF when trunking is disabled on the port. This value is set by the portCfgTrunkPort command. Long Distance Displays (..) or OFF when long distance mode is off; otherwise, displays long distance levels as follows: LE The link is up to 10 km. 52 Dell 8/4Gbps FC SAN Module Administrator's Guide 53-1001345-01

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
52
Dell 8/4Gbps FC SAN Module Administrator’s Guide
53-1001345-01
portCfgShow
B
Note
The execution of this command is subject to Virtual Fabric or Admin Domain restrictions that may
be in place. Refer to
“Understanding Virtual Fabric restrictions”
on page 32 snf
“Understanding
Admin Domain restrictions”
on page 33 for details.
Operands
This command has the following operand:
license
Specifies the license key to be installed. This operand is required.
Examples
To add a license key to the switch:
switch:admin>
licenseadd DXXtN3LmRSMWCSW3XmfSBPfrWKLZ3HMTN73rP9GANJMA
adding license-key [DXXtN3LmRSMWCSW3XmfSBPfrWKLZ3HMTN73rP9GANJMA]
portCfgShow
Displays port configuration settings.
Synopsis
portcfgshow
portcfgshow
[
slot
/]
port
portcfgshow
option
[
slot
/]
[
arguments
] [
optional
_
arguments
]
Description
Use this command to display the current configuration of a port. The behavior of this command is
platform-specific; output varies depending on port type and platform, and not all options are
supported on all platforms.
“Non-GbE port displays”
on page 52
If no operand is specified, this command displays port configuration settings for all ports on a
switch, except Gigabit Ethernet (GbE) ports.
Non-GbE port displays
The following information is displayed when the command is issued for all ports or for a specific
port:
Area Number
Displays the port area number. This field is displayed only when
portCfgShow
is executed for a specific port.
Speed
Displays Auto for auto speed negotiation mode, or a specific speed of 1, 2, 4,
or 8 Gbps. This value is set by the
portCfgSpeed
command.
Fill Word
Displays 0(Idle-Idle) or 1(arbff-arbff). This parameter is set by the
portcfgFillword
command.
AL_PA Offset 13
Displays (...) or OFF when the arbitrated loop physical address (AL_PA) on the
port is configured to use a 0x0 AL_PA address (default). Displays ON when
the address configuration is 0x13 AL_PA. This value is set by the
portCfgAlpa
command.
Trunk Port
Displays ON when port is set for trunking. Displays (..) or OFF when trunking is
disabled on the port. This value is set by the
portCfgTrunkPort
command.
Long Distance
Displays (..) or OFF when long distance mode is off; otherwise, displays long
distance levels as follows:
LE
The link is up to 10 km.