Dell PowerEdge T40 EMC Installation and Service Manual - Page 45

Expansion cards, Removing the Expansion card

Get Dell PowerEdge T40 PDF manuals and user guides View all Dell PowerEdge T40 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Figure 21. Installing power supply unit Next steps 1. Connect the PSU cable to the drive. 2. Open the PSU assembly. 3. Connect the PSU cables to the optical drive and the system board. NOTE: Route the cable properly when you replace it to prevent the cable from being pinched or crimped. 4. Close the PSU assembly. 5. Follow the procedure listed in After working inside your system. Expansion cards Removing the Expansion card Prerequisites 1. Follow the safety guidelines listed in Safety instructions. 2. Follow the procedure listed in Before working inside your system. 3. Open the PSU assembly. 4. If applicable, disconnect the cables connected to the expansion card. Steps 1. Push the ejector on the expansion card slot to release the expansion card. 2. Holding the card by its edge, pull the card to disengage it from the connector on the system board. 3. Remove the expansion card from the system. Figure 22. Removing the expansion card Installing and removing system components 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
Figure 21. Installing power supply unit
Next steps
1.
Connect the PSU cable to the drive.
2.
Open the PSU assembly
.
3.
Connect the PSU cables to the optical drive and the system board.
NOTE:
Route the cable properly when you replace it to prevent the cable from being pinched or crimped.
4.
Close the PSU assembly
.
5.
Follow the procedure listed in
After working inside your system
.
Expansion cards
Removing the Expansion card
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
.
2.
Follow the procedure listed in
Before working inside your system
.
3.
Open the PSU assembly
.
4.
If applicable, disconnect the cables connected to the expansion card.
Steps
1.
Push the ejector on the expansion card slot to release the expansion card.
2.
Holding the card by its edge, pull the card to disengage it from the connector on the system board.
3.
Remove the expansion card from the system.
Figure 22. Removing the expansion card
Installing and removing system components
45