Dell PowerEdge T40 EMC Installation and Service Manual - Page 52

System battery, Replacing the system battery

Get Dell PowerEdge T40 PDF manuals and user guides View all Dell PowerEdge T40 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

System battery Replacing the system battery Prerequisites WARNING: There is a danger of a new battery exploding if it is incorrectly installed. Replace the battery only with the same or equivalent type recommended by the manufacturer. For more information, see the safety information that shipped with your system. 1. Follow the safety guidelines listed in Safety instructions. 2. Follow the procedure listed in Before working inside your system. 3. If applicable, disconnect the power or data cables from expansion card(s). Steps 1. Locate the battery socket. For more information, see the System board jumpers and connectors section. CAUTION: To avoid damage to the battery connector, you must firmly support the connector while installing or removing a battery. 2. Use a plastic scribe to pry out the system battery. Figure 29. Removing the system battery 3. To install a new system battery, hold the battery with the positive side facing up and slide it under the securing tabs. 4. Press the battery into the connector until it snaps into place. Figure 30. Installing the system battery Next steps 1. If applicable, connect the cables to the expansion card(s). 2. Follow the procedure listed in After working inside your system. 3. While booting, press F2 to enter the System Setup and ensure that the battery is operating properly. 4. Enter the correct time and date in the System Setup Time and Date fields. 5. Exit the System Setup. 52 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
System battery
Replacing the system battery
Prerequisites
WARNING:
There is a danger of a new battery exploding if it is incorrectly installed. Replace the battery only with the
same or equivalent type recommended by the manufacturer. For more information, see the safety information that
shipped with your system.
1.
Follow the safety guidelines listed in
Safety instructions
.
2.
Follow the procedure listed in
Before working inside your system
.
3.
If applicable, disconnect the power or data cables from expansion card(s).
Steps
1.
Locate the battery socket. For more information, see the
System board jumpers and connectors
section.
CAUTION:
To avoid damage to the battery connector, you must firmly support the connector while installing or
removing a battery.
2.
Use a plastic scribe to pry out the system battery.
Figure 29. Removing the system battery
3.
To install a new system battery, hold the battery with the positive side facing up and slide it under the securing tabs.
4.
Press the battery into the connector until it snaps into place.
Figure 30. Installing the system battery
Next steps
1.
If applicable, connect the cables to the expansion card(s).
2.
Follow the procedure listed in
After working inside your system
.
3.
While booting, press F2 to enter the System Setup and ensure that the battery is operating properly.
4.
Enter the correct time and date in the System Setup
Time
and
Date
fields.
5.
Exit the System Setup.
52
Installing and removing system components