Dell PowerSwitch S4820T Configuration Guide for the S4820T System 9.14.1.0 - Page 315

Dell(conf-if-te-0/0)#ip address 10.1.1.1/24 Dell(conf-if-te-0/0)#ip address 11.1.1.1/24 secondary Dell(conf-if-te-0/0)#ip helper-address 2.1.1.1 Dell(conf-if-te-0/0)#no shutdown Dell(conf-if-te-0/0)# DHCP relay tries to get ip address for the client, through configured primary address filling giaddr (relay address) 10.1.1.1. If there is no OFFER from DHCP Server, for three DISCOVER retries. Since secondary-subnet enabled, DHCP Relay Agent tries to get ip address through secondary ip address filling giaddr (relay address) 11.1.1.1. 3 To disable the DHCP relay secondary-subnet: Dell(conf)# no ip dhcp relay secondary-subnet Drop DHCP Packets on Snooped VLANs Only Binding table entries are deleted when a lease expires or the relay agent encounters a DHCPRELEASE. Line cards maintain a list of snooped VLANs. When the binding table fills, DHCP packets are dropped only on snooped VLANs, while such packets are forwarded across non-snooped VLANs. Because DHCP packets are dropped, no new IP address assignments are made. However, DHCP release and decline packets are allowed so that the DHCP snooping table can decrease in size. After the table usage falls below the maximum limit of 4000 entries, new IP address assignments are allowed. To view the number of entries in the table, use the show ip dhcp snooping binding command. This output displays the snooping binding table created using the ACK packets from the trusted port. DellEMC#show ip dhcp snooping binding Codes : S - Static D - Dynamic IP Address MAC Address Expires(Sec) Type VLAN Interface 10.1.1.251 00:00:4d:57:f2:50 172800 D Vl 10 Te 1/2 10.1.1.252 00:00:4d:57:e6:f6 172800 D Vl 10 Te 1/1 10.1.1.253 00:00:4d:57:f8:e8 172740 D Vl 10 Te 1/3 10.1.1.254 00:00:4d:69:e8:f2 172740 D Vl 10 Te 1/5 Total number of Entries in the table : 4 Dynamic ARP Inspection Dynamic address resolution protocol (ARP) inspection prevents ARP spoofing by forwarding only ARP frames that have been validated against the DHCP binding table. ARP is a stateless protocol that provides no authentication mechanism. Network devices accept ARP requests and replies from any device. ARP replies are accepted even when no request was sent. If a client receives an ARP message for which a relevant entry already exists in its ARP cache, it overwrites the existing entry with the new information. The lack of authentication in ARP makes it vulnerable to spoofing. ARP spoofing is a technique attackers use to inject false IP-to-MAC mappings into the ARP cache of a network device. It is used to launch man-in-the-middle (MITM), and denial-of-service (DoS) attacks, among others. A spoofed ARP message is one in which the MAC address in the sender hardware address field and the IP address in the sender protocol field are strategically chosen by the attacker. For example, in an MITM attack, the attacker sends a client an ARP message containing the attacker's MAC address and the gateway's IP address. The client then thinks that the attacker is the gateway, and sends all internet-bound packets to it. Likewise, the attacker sends the gateway an ARP message containing the attacker's MAC address and the client's IP address. The gateway then thinks that the attacker is the client and forwards all packets addressed to the client to it. As a result, the attacker is able to sniff all packets to and from the client. Other attacks using ARP spoofing include: Dynamic Host Configuration Protocol (DHCP) 315