Dell PowerSwitch S4820T Configuration Guide for the S4820T System 9.14.1.0 - Page 642

The first bold lines assign an IP address to a Layer 3 interface, and theno shutdown command ensures that the interface is UP. The second bold line assigns the IP address of an interface to an area. Example of Enabling OSPFv2 and Assigning an Area to an Interface DellEMC#(conf)#int te 4/14 Dell(conf-if-te-4/14)#ip address 10.10.10.10/24 DellEMC(conf-if-te-4/14)#no shutdown DellEMC(conf-if-te-4/14)#ex DellEMC(conf)#router ospf 1 DellEMC(conf-router_ospf-1)#network 1.2.3.4/24 area 0 DellEMC(conf-router_ospf-1)#network 10.10.10.10/24 area 1 DellEMC(conf-router_ospf-1)#network 20.20.20.20/24 area 2 DellEMC(conf-router_ospf-1)# DellEMC# Dell EMC Networking recommends using the interface IP addresses for the OSPFv2 router ID for easier management and troubleshooting. To view the configuration, use the show config command in CONFIGURATION ROUTER OSPF mode. OSPF, by default, sends hello packets out to all physical interfaces assigned an IP address that is a subset of a network on which OSPF is enabled. To view currently active interfaces and the areas assigned to them, use the show ip ospf interface command. Example of Viewing Active Interfaces and Assigned Areas DellEMC>show ip ospf 1 interface TenGigabitEthernet 1/17 is up, line protocol is up Internet Address 10.2.2.1/24, Area 0.0.0.0 Process ID 1, Router ID 11.1.2.1, Network Type BROADCAST, Cost: 1 Transmit Delay is 1 sec, State DR, Priority 1 Designated Router (ID) 11.1.2.1, Interface address 10.2.2.1 Backup Designated Router (ID) 0.0.0.0, Interface address 0.0.0.0 Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 Hello due in 00:00:04 Neighbor Count is 0, Adjacent neighbor count is 0 TenGigabitEthernet 1/21 is up, line protocol is up Internet Address 10.2.3.1/24, Area 0.0.0.0 Process ID 1, Router ID 11.1.2.1, Network Type BROADCAST, Cost: 1 Transmit Delay is 1 sec, State BDR, Priority 1 Designated Router (ID) 13.1.1.1, Interface address 10.2.3.2 Backup Designated Router (ID) 11.1.2.1, Interface address 10.2.3.1 Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 Hello due in 00:00:05 Neighbor Count is 1, Adjacent neighbor count is 1 Adjacent with neighbor 13.1.1.1 (Designated Router) DellEMC> Loopback interfaces also help the OSPF process. OSPF picks the highest interface address as the router-id and a Loopback interface address has a higher precedence than other interface addresses. Example of Viewing OSPF Status on a Loopback Interface DellEMC#show ip ospf 1 int TenGigabitEthernet 1/23 is up, line protocol is up Internet Address 10.168.0.1/24, Area 0.0.0.1 Process ID 1, Router ID 10.168.253.2, Network Type BROADCAST, Cost: 1 Transmit Delay is 1 sec, State DROTHER, Priority 1 Designated Router (ID) 10.168.253.5, Interface address 10.168.0.4 Backup Designated Router (ID) 192.168.253.3, Interface address 10.168.0.2 Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 Hello due in 00:00:08 Neighbor Count is 3, Adjacent neighbor count is 2 642 Open Shortest Path First (OSPFv2 and OSPFv3)