Dell Studio Hybrid Studio Slim Service Manual - Page 17

Replacing the FlexDock

Get Dell Studio Hybrid Studio Slim PDF manuals and user guides View all Dell Studio Hybrid Studio Slim manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

6. Press the two spring clamps and slide out the Media Card Reader along with the FlexBay drive cage from the FlexBay slot. 7. Remove the two screws holding the Media Card Reader in the FlexBay drive cage. 8. Lift the Media Card Reader to separate it from the FlexBay drive cage. 1 FlexBay drive cage 3 cage notch (2) 5 screws (2) 2 spring clamps (2) 4 Media Card Reader 9. If you are not reinstalling the Media Card Reader: a. Replace the optical drive (see Replacing the Optical Drive) b. Reinstall the FlexBay drive insert. c. Replace the front panel (see Replacing the Front Panel'). d. Replace the computer cover (see Replacing the Computer Cover). 10. If you are installing a new Media Card Reader, remove the Media Card Reader from its packaging. 11. Remove the FlexBay drive insert (see Replacing the FlexBay/FlexDock Drive Insert). 12. Press the two spring clamps and slide out the FlexBay drive cage from the front of the system. 13. Place the Media Card Reader in the FlexBay drive cage and slide it towards the cage notch to align the cage notch with the notch holes in the Media Card Reader. 14. Align the two screw holes on the Media Card Reader with the FlexBay drive cage. 15. Tighten the two screws to secure the Media Card Reader in the FlexBay drive cage. 16. Slide the FlexBay drive cage along with the Media Card Reader in the FlexBay slot till it snaps in place. NOTE: Ensure that the Media Card Reader is installed before the FlexBay cable is connected. 17. Connect the FlexBay USB cable to the back of the Media Card Reader and to the internal USB connector (F_USB5) on the system board (see System Board Components). 18. Replace the optical drive (see Replacing the Optical Drive). 19. Replace the front panel (see Replacing the Front Panel). 20. Replace the computer cover (see Replacing the Computer Cover). 21. Connect your computer and devices to electrical outlets, and then turn them on. Replacing the FlexDock 1. Follow the procedures in Before You Begin. 2. Remove the computer cover (see Replacing the Computer Cover).

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
6.
Press the two spring clamps and slide out the Media Card Reader along with the FlexBay drive cage from the FlexBay slot.
7.
Remove the two screws holding the Media Card Reader in the FlexBay drive cage.
8.
Lift the Media Card Reader to separate it from the FlexBay drive cage.
9.
If you are not reinstalling the Media Card Reader:
a.
Replace the optical drive (see
Replacing the Optical Drive
)
b.
Reinstall the FlexBay drive insert.
c.
Replace the front panel (see
Replacing the Front Panel
').
d.
Replace the computer cover (see
Replacing the Computer Cover
).
10.
If you are installing a new Media Card Reader, remove the Media Card Reader from its packaging.
11.
Remove the FlexBay drive insert (see
Replacing the FlexBay/FlexDock Drive Insert
).
12.
Press the two spring clamps and slide out the FlexBay drive cage from the front of the system.
13.
Place the Media Card Reader in the FlexBay drive cage and slide it towards the cage notch to align the cage notch with the notch holes in the Media
Card Reader.
14.
Align the two screw holes on the Media Card Reader with the FlexBay drive cage.
15.
Tighten the two screws to secure the Media Card Reader in the FlexBay drive cage.
16.
Slide the FlexBay drive cage along with the Media Card Reader in the FlexBay slot till it snaps in place.
17.
Connect the FlexBay USB cable to the back of the Media Card Reader and to the internal USB connector (F_USB5) on the system board (see
System
Board Components
).
18.
Replace the optical drive (see
Replacing the Optical Drive
).
19.
Replace the front panel (see
Replacing the Front Panel
).
20.
Replace the computer cover (see
Replacing the Computer Cover
).
21.
Connect your computer and devices to electrical outlets, and then turn them on.
Replacing the FlexDock
1.
Follow the procedures in
Before You Begin
.
2.
Remove the computer cover (see
Replacing the Computer Cover
).
1
FlexBay drive cage
2
spring clamps (2)
3
cage notch (2)
4
Media Card Reader
5
screws (2)
NOTE:
Ensure that the Media Card Reader is installed before the FlexBay cable is connected.