Dell Vostro 5402 Service Manual - Page 79

Installing the display assembly - discrete

Get Dell Vostro 5402 PDF manuals and user guides View all Dell Vostro 5402 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 79 highlights

Steps 1. Locate the display cable and display hinges on your computer. 2. Remove the transparent sticker covering the display cable to the system board. 3. Peel the tape that secures the display cable to the system board. 4. Open the latch, and disconnect the display cable from the system board. 5. Remove the two screws (M2.5x4) and (M2x3) that secure the left-display hinge to the system board. 6. Remove the two screws (M2.5x4) that secure the right-display hinge to the system board. 7. Open the display hinges at an angle of 90 degrees. 8. Gently slide the palm-rest and keyboard assembly off the display assembly carefully. Installing the display assembly - discrete Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The figure indicates the location of the component and provides a visual representation of the installation procedure. Disassembly and reassembly 79

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
Steps
1.
Locate the display cable and display hinges on your computer.
2.
Remove the transparent sticker covering the display cable to the system board.
3.
Peel the tape that secures the display cable to the system board.
4.
Open the latch, and disconnect the display cable from the system board.
5.
Remove the two screws (M2.5x4) and (M2x3) that secure the left-display hinge to the system board.
6.
Remove the two screws (M2.5x4) that secure the right-display hinge to the system board.
7.
Open the display hinges at an angle of 90 degrees.
8.
Gently slide the palm-rest and keyboard assembly off the display assembly carefully.
Installing the display assembly - discrete
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The figure indicates the location of the component and provides a visual representation of the installation procedure.
Disassembly and reassembly
79