Home » Dell Manuals » Wireless » Dell W-Series 207 » Manual Viewer

Dell W-Series 207 Instant 6.5.1.0-4.3.1.0 User Guide - Page 104

Wired Profiles, Configuring a Wired Profile

Add to My Manuals
Save this manual to your list of manuals

Page 104 highlights

Chapter 11 Wired Profiles This chapter describes the following procedures: l Configuring a Wired Profile on page 104 l Assigning a Profile to Ethernet Ports on page 109 l Editing a Wired Profile on page 109 l Deleting a Wired Profile on page 110 l Link Aggregation Control Protocol on page 110 l Understanding Hierarchical Deployment on page 111 Configuring a Wired Profile The Ethernet ports allow third-party devices such as VoIP phones or printers (which support only wired connections) to connect to the wireless network. You can also configure an Access Control List (ACL) for additional security on the Ethernet downlink. The wired profile configuration for Employee network involves the following procedures: 1. Configuring Wired Settings on page 104 2. Configuring VLAN for a Wired Profile on page 105 3. Configuring Security Settings for a Wired Profile on page 106 4. Configuring Access Rules for a Wired Profile on page 107 For information on creating a wired profile for guest network, see Captive Portal for Guest Access. Configuring Wired Settings You can configure wired settings for a wired profile by using the Instant UI or the CLI. In the Instant UI 1. Click the Wired link under More on the Instant main window. The Wired window is displayed. 2. Click New under Wired Networks. The New Wired Network window is displayed. 3. Click the Wired Settings tab and configure the following parameters: a. Name-Specify a name for the profile. b. Primary Usage-Select Employee or Guest. c. Speed/Duplex-Ensure that appropriate values are selected for Speed/Duplex. Contact your network administrator if you need to assign speed and duplex parameters. d. POE-Set POE to Enabled to enable Power over Ethernet. e. Admin Status-Ensure that an appropriate value is selected. The Admin Status indicates if the port is up or down. 4. Click Show advanced options and configure the following parameters as required: a. Content Filtering-To ensure that all DNS requests to non-corporate domains on this wired network are sent to OpenDNS, select Enabled for Content Filtering. b. Uplink-Select Enabled to configure uplink on this wired profile. If Uplink is set to Enabled and this network profile is assigned to a specific port, the port will be enabled as Uplink port. For more Dell Networking W-Series Instant 6.5.1.0-4.3.1.0 | User Guide Wired Profiles | 104

Section	Page
About this Guide	9
Intended Audience	9
Related Documents	9
Conventions	9
Contacting Dell	10
About Instant	11
Instant Overview	11
What is New in this Release	14
Setting up a W-IAP	16
Setting up Instant Network	16
Provisioning a W-IAP	17
Logging in to the Instant UI	19
Accessing the Instant CLI	20
Automatic Retrieval of Configuration	24
Managed Mode Operations	24
Prerequisites	24
Configuring Managed Mode Parameters	25
Verifying the Configuration	26
Instant User Interface	28
Login Screen	28
Main Window	29
Initial Configuration Tasks	56
Configuring System Parameters	56
Changing Password	62
Customizing W-IAP Settings	63
Modifying the W-IAP Host Name	63
Configuring Zone Settings on a W-IAP	63
Specifying a Method for Obtaining IP Address	64
Configuring External Antenna	65
Configuring Radio Profiles for a W-IAP	66
Configuring Uplink VLAN for a W-IAP	68
Changing the W-IAP Installation Mode	68
Changing USB Port Status	69
Master Election and Virtual Controller	70
Adding a W-IAP to the Network	71
Removing a W-IAP from the Network	72
VLAN Configuration	73
VLAN Pooling	73
Uplink VLAN Monitoring and Detection on Upstream Devices	73
IPv6 Support	74
IPv6 Notation	74
Enabling IPv6 Support for W-IAP Configuration	74
Firewall Support for IPv6	76
Debugging Commands	76
Wireless Network Profiles	77
Configuring Wireless Network Profiles	77
Configuring Fast Roaming for Wireless Clients	97
Configuring Modulation Rates on a WLAN SSID	100
Multi-User-MIMO	101
Management Frame Protection	102
Disabling Short Preamble for Wireless Client	102
Editing Status of a WLAN SSID Profile	102
Editing a WLAN SSID Profile	103
Deleting a WLAN SSID Profile	103
Wired Profiles	104
Configuring a Wired Profile	104
Assigning a Profile to Ethernet Ports	109
Editing a Wired Profile	109
Deleting a Wired Profile	110
Link Aggregation Control Protocol	110
Understanding Hierarchical Deployment	111
Captive Portal for Guest Access	113
Understanding Captive Portal	113
Configuring a WLAN SSID for Guest Access	114
Configuring Wired Profile for Guest Access	120
Configuring Internal Captive Portal for Guest Network	122
Configuring External Captive Portal for a Guest Network	125
Configuring Facebook Login	131
Configuring Guest Logon Role and Access Rules for Guest Users	132
Configuring Captive Portal Roles for an SSID	134
Configuring Walled Garden Access	137
Authentication and User Management	139
Managing W-IAP Users	139
Supported Authentication Methods	143
Supported EAP Authentication Frameworks	145
Configuring Authentication Servers	146
Understanding Encryption Types	160
Configuring Authentication Survivability	161
Configuring 802.1X Authentication for a Network Profile	163
Enabling 802.1X Supplicant Support	165
Configuring MAC Authentication for a Network Profile	166
Configuring MAC Authentication with 802.1X Authentication	168
Configuring MAC Authentication with Captive Portal Authentication	170
Configuring WISPr Authentication	171
Blacklisting Clients	172
Uploading Certificates	175
Roles and Policies	178
Firewall Policies	178
Content Filtering	191
Configuring User Roles	195
Configuring Derivation Rules	197
Using Advanced Expressions in Role and VLAN Derivation Rules	203
DHCP Configuration	207
Configuring DHCP Scopes	207
Configuring the Default DHCP Scope for Client IP Assignment	214
Configuring Time-Based Services	217
Time Range Profiles	217
Configuring a Time Range Profile	217
Applying a Time Range Profile to a WLAN SSID	218
Verifying the Configuration	219
Dynamic DNS Registration	221
Enabling Dynamic DNS	221
Configuring Dynamic DNS Updates for Clients	222
Verifying the Configuration	223
VPN Configuration	224
Understanding VPN Features	224
Configuring a Tunnel from a W-IAP to a Mobility Controller	225
Configuring Routing Profiles	236
IAP-VPN Deployment	238
Understanding IAP-VPN Architecture	238
Configuring W-IAP and Controller for IAP-VPN Operations	241
Adaptive Radio Management	249
ARM Overview	249
Configuring ARM Features on a W-IAP	250
Configuring Radio Settings	256
Deep Packet Inspection and Application Visibility	261
Deep Packet Inspection	261
Enabling Application Visibility	261
Application Visibility	262
Enabling URL Visibility	267
Configuring ACL Rules for Application and Application Categories	267
Configuring Web Policy Enforcement Service	270
Voice and Video	273
Wi-Fi Multimedia Traffic Management	273
Media Classification for Voice and Video Calls	276
Enabling Enhanced Voice Call Tracking	277
Services	279
Configuring AirGroup	279
Configuring a W-IAP for RTLS Support	288
Configuring a W-IAP for Analytics and Location Engine Support	289
Managing BLE Beacons	290
Clarity Live	291
Configuring OpenDNS Credentials	293
Integrating a W-IAP with Palo Alto Networks Firewall	293
Integrating a W-IAP with an XML API Interface	295
CALEA Integration and Lawful Intercept Compliance	298
Cluster Security	304
Overview	304
Enabling Cluster Security	305
Cluster Security Debugging Logs	305
Verifying the Configuration	306
W-IAP Management and Monitoring	307
Managing a W-IAP from W-AirWave	307
Uplink Configuration	318
Uplink Interfaces	318
Uplink Preferences and Switching	323
Intrusion Detection	328
Detecting and Classifying Rogue W-IAPs	328
OS Fingerprinting	328
Configuring Wireless Intrusion Protection and Detection Levels	329
Configuring IDS	334
Mesh W-IAP Configuration	335
Mesh Network Overview	335
Setting up Instant Mesh Network	336
Configuring Wired Bridging on Ethernet 0 for Mesh Point	336
Mobility and Client Management	338
Layer-3 Mobility Overview	338
Configuring L3-Mobility	339
Spectrum Monitor	341
Understanding Spectrum Data	341
Configuring Spectrum Monitors and Hybrid W-IAPs	347
W-IAP Maintenance	349
Upgrading a W-IAP	349
Backing up and Restoring W-IAP Configuration Data	352
Converting a W-IAP to a Remote AP and Campus AP	353
Resetting a Remote AP or Campus AP to a W-IAP	359
Rebooting the W-IAP	359
Monitoring Devices and Logs	361
Configuring SNMP	361
Configuring a Syslog Server	365
Configuring TFTP Dump Server	366
Running Debug Commands	367
Uplink Bandwidth Monitoring	371
Hotspot Profiles	373
Understanding Hotspot Profiles	373
Configuring Hotspot Profiles	375
Sample Configuration	386
ClearPass Guest Setup	389
Configuring ClearPass Guest	389
Verifying ClearPass Guest Setup	392
Troubleshooting	392
IAP-VPN Deployment Scenarios	394
Scenario 1—IPsec: Single Datacenter Deployment with No Redundancy	395
Scenario 2—IPsec: Single Datacenter with Multiple Controllers for Redundancy	399
Scenario 3—IPsec: Multiple Datacenter Deployment with Primary and Backup Cont...	403
Scenario 4—GRE: Single Datacenter Deployment with No Redundancy	408
Glossary	411
Acronyms and Abbreviations	416

Match case Limit results 1 per page

Dell Networking W-Series Instant 6.5.1.0-4.3.1.0 | User Guide

Wired Profiles |

104

Chapter 11

Wired Profiles

This chapter describes the following procedures:

Configuring a Wired Profile on page 104

Assigning a Profile to Ethernet Ports on page 109

Editing a Wired Profile on page 109

Deleting a Wired Profile on page 110

Link Aggregation Control Protocol on page 110

Understanding Hierarchical Deployment on page 111

Configuring a Wired Profile

The Ethernet ports allow third-party devices such as VoIP phones or printers (which support only wired

connections) to connect to the wireless network. You can also configure an Access Control List (ACL) for

additional security on the Ethernet downlink.

The wired profile configuration for Employee network involves the following procedures:

Configuring Wired Settings on page 104

Configuring VLAN for a Wired Profile on page 105

Configuring Security Settings for a Wired Profile on page 106

Configuring Access Rules for a Wired Profile on page 107

For information on creating a wired profile for guest network, see

Captive Portal for Guest Access

Configuring Wired Settings

You can configure wired settings for a wired profile by using the Instant UI or the CLI.

In the Instant UI

1. Click the

Wired

link under

on the Instant main window. The

Wired

window is displayed.

2. Click

New

under

Wired Networks

. The

New Wired Network

window is displayed.

3. Click the

Wired Settings

tab and configure the following parameters:

Name

—Specify a name for the profile.

Primary Usage

—Select

Employee

Guest

Speed/Duplex

—Ensure that appropriate values are selected for

Speed/Duplex

. Contact your network

administrator if you need to assign speed and duplex parameters.

POE

—Set

POE

Enabled

to enable Power over Ethernet.

Admin Status

—Ensure that an appropriate value is selected. The

Admin Status

indicates if the port is

up or down.

4. Click

Show advanced options

and configure the following parameters as required:

Content Filtering

—To ensure that all DNS requests to non-corporate domains on this wired network

are sent to OpenDNS, select

Enabled

for

Content Filtering

Uplink

—Select

Enabled

to configure uplink on this wired profile. If

Uplink

is set to

Enabled

and this

network profile is assigned to a specific port, the port will be enabled as Uplink port. For more