Home » Dell Manuals » Wireless » Dell W-Series 207 » Manual Viewer

Dell W-Series 207 Instant 6.5.1.0-4.3.1.0 User Guide - Page 231

More > VPN, Tunneling, L2TPv3, Protocol,

Add to My Manuals
Save this manual to your list of manuals

Page 231 highlights

l If the primary LNS is down, it fails over to the backup LNS. L2TPv3 has one tunnel profile, and under this a primary peer and a backup peer are configured. If the primary tunnel creation fails or if the primary tunnel gets deleted, the backup starts. The following two failover modes are supported: n Preemptive: In this mode, if the primary comes up when the backup is active, the backup tunnel is deleted and the primary tunnel resumes as an active tunnel. If you configure the tunnel to be preemptive, and when the primary tunnel goes down, it starts the persistence timer which tries to bring up the primary tunnel. n Non-Preemptive: In this mode, when the backup tunnel is established after the primary tunnel goes down, it does not make the primary tunnel active again. L2TPV3 is not supported on W-IAP205 devices. You can configure an L2TPv3 tunnel and session profiles through the Instant UI or the CLI. In the Instant UI To configure an L2TPv3 tunnel and session profile: 1. Click the More > VPN link located directly above the Search bar in the Instant UI. The Tunneling window is displayed. Figure 54 L2TPv3 Tunneling 2. Select L2TPv3 from the Protocol drop-down list. 3. To configure the tunnel profile: a. Click the New button. b. Enter the tunnel name to be used for tunnel creation. 231 | VPN Configuration Dell Networking W-Series Instant 6.5.1.0-4.3.1.0 | User Guide

Section	Page
About this Guide	9
Intended Audience	9
Related Documents	9
Conventions	9
Contacting Dell	10
About Instant	11
Instant Overview	11
What is New in this Release	14
Setting up a W-IAP	16
Setting up Instant Network	16
Provisioning a W-IAP	17
Logging in to the Instant UI	19
Accessing the Instant CLI	20
Automatic Retrieval of Configuration	24
Managed Mode Operations	24
Prerequisites	24
Configuring Managed Mode Parameters	25
Verifying the Configuration	26
Instant User Interface	28
Login Screen	28
Main Window	29
Initial Configuration Tasks	56
Configuring System Parameters	56
Changing Password	62
Customizing W-IAP Settings	63
Modifying the W-IAP Host Name	63
Configuring Zone Settings on a W-IAP	63
Specifying a Method for Obtaining IP Address	64
Configuring External Antenna	65
Configuring Radio Profiles for a W-IAP	66
Configuring Uplink VLAN for a W-IAP	68
Changing the W-IAP Installation Mode	68
Changing USB Port Status	69
Master Election and Virtual Controller	70
Adding a W-IAP to the Network	71
Removing a W-IAP from the Network	72
VLAN Configuration	73
VLAN Pooling	73
Uplink VLAN Monitoring and Detection on Upstream Devices	73
IPv6 Support	74
IPv6 Notation	74
Enabling IPv6 Support for W-IAP Configuration	74
Firewall Support for IPv6	76
Debugging Commands	76
Wireless Network Profiles	77
Configuring Wireless Network Profiles	77
Configuring Fast Roaming for Wireless Clients	97
Configuring Modulation Rates on a WLAN SSID	100
Multi-User-MIMO	101
Management Frame Protection	102
Disabling Short Preamble for Wireless Client	102
Editing Status of a WLAN SSID Profile	102
Editing a WLAN SSID Profile	103
Deleting a WLAN SSID Profile	103
Wired Profiles	104
Configuring a Wired Profile	104
Assigning a Profile to Ethernet Ports	109
Editing a Wired Profile	109
Deleting a Wired Profile	110
Link Aggregation Control Protocol	110
Understanding Hierarchical Deployment	111
Captive Portal for Guest Access	113
Understanding Captive Portal	113
Configuring a WLAN SSID for Guest Access	114
Configuring Wired Profile for Guest Access	120
Configuring Internal Captive Portal for Guest Network	122
Configuring External Captive Portal for a Guest Network	125
Configuring Facebook Login	131
Configuring Guest Logon Role and Access Rules for Guest Users	132
Configuring Captive Portal Roles for an SSID	134
Configuring Walled Garden Access	137
Authentication and User Management	139
Managing W-IAP Users	139
Supported Authentication Methods	143
Supported EAP Authentication Frameworks	145
Configuring Authentication Servers	146
Understanding Encryption Types	160
Configuring Authentication Survivability	161
Configuring 802.1X Authentication for a Network Profile	163
Enabling 802.1X Supplicant Support	165
Configuring MAC Authentication for a Network Profile	166
Configuring MAC Authentication with 802.1X Authentication	168
Configuring MAC Authentication with Captive Portal Authentication	170
Configuring WISPr Authentication	171
Blacklisting Clients	172
Uploading Certificates	175
Roles and Policies	178
Firewall Policies	178
Content Filtering	191
Configuring User Roles	195
Configuring Derivation Rules	197
Using Advanced Expressions in Role and VLAN Derivation Rules	203
DHCP Configuration	207
Configuring DHCP Scopes	207
Configuring the Default DHCP Scope for Client IP Assignment	214
Configuring Time-Based Services	217
Time Range Profiles	217
Configuring a Time Range Profile	217
Applying a Time Range Profile to a WLAN SSID	218
Verifying the Configuration	219
Dynamic DNS Registration	221
Enabling Dynamic DNS	221
Configuring Dynamic DNS Updates for Clients	222
Verifying the Configuration	223
VPN Configuration	224
Understanding VPN Features	224
Configuring a Tunnel from a W-IAP to a Mobility Controller	225
Configuring Routing Profiles	236
IAP-VPN Deployment	238
Understanding IAP-VPN Architecture	238
Configuring W-IAP and Controller for IAP-VPN Operations	241
Adaptive Radio Management	249
ARM Overview	249
Configuring ARM Features on a W-IAP	250
Configuring Radio Settings	256
Deep Packet Inspection and Application Visibility	261
Deep Packet Inspection	261
Enabling Application Visibility	261
Application Visibility	262
Enabling URL Visibility	267
Configuring ACL Rules for Application and Application Categories	267
Configuring Web Policy Enforcement Service	270
Voice and Video	273
Wi-Fi Multimedia Traffic Management	273
Media Classification for Voice and Video Calls	276
Enabling Enhanced Voice Call Tracking	277
Services	279
Configuring AirGroup	279
Configuring a W-IAP for RTLS Support	288
Configuring a W-IAP for Analytics and Location Engine Support	289
Managing BLE Beacons	290
Clarity Live	291
Configuring OpenDNS Credentials	293
Integrating a W-IAP with Palo Alto Networks Firewall	293
Integrating a W-IAP with an XML API Interface	295
CALEA Integration and Lawful Intercept Compliance	298
Cluster Security	304
Overview	304
Enabling Cluster Security	305
Cluster Security Debugging Logs	305
Verifying the Configuration	306
W-IAP Management and Monitoring	307
Managing a W-IAP from W-AirWave	307
Uplink Configuration	318
Uplink Interfaces	318
Uplink Preferences and Switching	323
Intrusion Detection	328
Detecting and Classifying Rogue W-IAPs	328
OS Fingerprinting	328
Configuring Wireless Intrusion Protection and Detection Levels	329
Configuring IDS	334
Mesh W-IAP Configuration	335
Mesh Network Overview	335
Setting up Instant Mesh Network	336
Configuring Wired Bridging on Ethernet 0 for Mesh Point	336
Mobility and Client Management	338
Layer-3 Mobility Overview	338
Configuring L3-Mobility	339
Spectrum Monitor	341
Understanding Spectrum Data	341
Configuring Spectrum Monitors and Hybrid W-IAPs	347
W-IAP Maintenance	349
Upgrading a W-IAP	349
Backing up and Restoring W-IAP Configuration Data	352
Converting a W-IAP to a Remote AP and Campus AP	353
Resetting a Remote AP or Campus AP to a W-IAP	359
Rebooting the W-IAP	359
Monitoring Devices and Logs	361
Configuring SNMP	361
Configuring a Syslog Server	365
Configuring TFTP Dump Server	366
Running Debug Commands	367
Uplink Bandwidth Monitoring	371
Hotspot Profiles	373
Understanding Hotspot Profiles	373
Configuring Hotspot Profiles	375
Sample Configuration	386
ClearPass Guest Setup	389
Configuring ClearPass Guest	389
Verifying ClearPass Guest Setup	392
Troubleshooting	392
IAP-VPN Deployment Scenarios	394
Scenario 1—IPsec: Single Datacenter Deployment with No Redundancy	395
Scenario 2—IPsec: Single Datacenter with Multiple Controllers for Redundancy	399
Scenario 3—IPsec: Multiple Datacenter Deployment with Primary and Backup Cont...	403
Scenario 4—GRE: Single Datacenter Deployment with No Redundancy	408
Glossary	411
Acronyms and Abbreviations	416

Match case Limit results 1 per page

231

| VPN Configuration

Dell Networking W-Series Instant 6.5.1.0-4.3.1.0 | User Guide

If the primary LNS is down, it fails over to the backup LNS. L2TPv3 has one tunnel profile, and under this a

primary peer and a backup peer are configured. If the primary tunnel creation fails or if the primary tunnel

gets deleted, the backup starts. The following two failover modes are supported:

Preemptive: In this mode, if the primary comes up when the backup is active, the backup tunnel is

deleted and the primary tunnel resumes as an active tunnel. If you configure the tunnel to be

preemptive, and when the primary tunnel goes down, it starts the persistence timer which tries to bring

up the primary tunnel.

Non-Preemptive: In this mode, when the backup tunnel is established after the primary tunnel goes

down, it does not make the primary tunnel active again.

L2TPV3 is not supported on W-IAP205 devices.

You can configure an L2TPv3 tunnel and session profiles through the Instant UI or the CLI.

In the Instant UI

To configure an L2TPv3 tunnel and session profile:

1. Click the

More > VPN

link located directly above the Search bar in the Instant UI. The

Tunneling

window is

displayed.

Figure 54

L2TPv3 Tunneling

2. Select

L2TPv3

from the

Protocol

drop-down list.

3. To configure the tunnel profile:

Click the

New

button.

b. Enter the tunnel name to be used for tunnel creation.