Denon 4310CI Owners Manual - Page 112

BuRompaiqnwi [Audio] Symptom Cause / Countermeasure No sound is produced • When playing monaural audio sources, select a surround mode from center speaker. other than "STANDARD" (Dolby/DTS Surround). No sound is produced • Set the surround mode to a mode for surround playback. from surround speakers. No sound is produced from surround back speaker. • Check that the surround back speaker's power amplifier assignment is set to "Normal". • Set the surround back speakers to something other than "None". • Set "Surround Parameter" - "Surround Back" to something other than "OFF". • Set the surround mode to the surround playback mode. No sound is produced from subwoofer. • Turn on the subwoofer's power. • Set the subwoofer to "Yes". • Check the subwoofer connections. • Increase the subwoofer's channel level. DTS sound is not output. • Set the Blu-ray disc/DVD player's audio output setting to "Bitstream". For details, refer to the Blu-ray disc/DVD player's operating instructions. • Use a DTS-compatible Blu-ray disc player/DVD player. • Set the decode mode to "Auto" or "DTS". Dolby TrueHD, DTSHD, Dolby Digital Plus audio is not output. • Make HDMI connections. • Set the Blu-ray disc/DVD player's audio output setting to "Bit- stream". For details, refer to the Blu-ray disc/DVD player's operating instructions. • Use a DTS-compatible Blu-ray disc player. Page 71, 72 71, 72 34 35 74 71, 72 34 13 36 - 50 14 [Control dock for iPod] Symptom Cause / Countermeasure iPod cannot played. be • Connect to the terminal to which "iPod dock" was assigned and switch the input source. • Check the iPod connections. • Plug the control dock for iPod's AC adapter into a power outlet. Communications with the AVR-4310C1 are not possible unless the AC adapter is plugged in. • Some iPods do not support being used connected directly to the USB port. Page 27, 48 16 21 109 [Video] Symptom Cause / Countermeasure, . No picture appears. • Check the connections of the AVR-4310CI's video output , terminals and the TV's input terminals. • Make the proper input setting for the input terminals of the TV connected to the AVR-4310C1. • Cancel the PURE DIRECT mode. • High definition (1080i/720p) and progressive (480p/576p) video signals are not down-converted. Set the player to interlace (480i/576i) signals. • Check the "Video Select" setting. Picture cannot recorded. be • The REC OUT video terminal does not have a video conversion function, so use a video cable to input video signals, an S-Video cable to input S-Video signals. DVDs cannot be • This is not a malfunction. Most movie software includes copy copied on a VCR. prevention signals and cannot be copied. GUI is not displayed. • Set "Format" according to the format INTSC or PAL) of the TV being used. Page 14, 15 72 48 17 43 [HDMI] Symptom Cause / Countermeasure HDMI audio signals are not output from speakers. • Set "HDMI Audio Out" to "AMP" to output HDMI audio signals from the speakers. No picture appears with HDMI connections. • Check the connection of the HDMI connectors. • Select the input source assigned to the HDMI terminal at "HDMI". • Connect a monitor that is compatible with copyright protection (HDCP). • Check that the output format (HDMI FORMAT) of the connected player, etc., matches the TV's compatible input formats. • Depending on the monitor you have connected, the display may not be correct when you set to "Auto (Dual)". In such a case, set to either "Monitor 1" or "Monitor 2". No sound is output from the monitor connected with HDMI connections. • Set "HDMI Audio Out" to "TV" to output HDMI audio signals from the TV. When performing the • Set "HDMI Control" - "Control" to "OFF". When you only want following operations to operate the power on/off each device, set "Power Off Control" on a connected to "OFF". device, AVR-4310C1 has the same operations. • Power ON/OFF • Switching audio output devices • Adjust volume • Switch input source Page 37 14 27, 47 14 14, 15 37 37 37