Denon 4310CI Owners Manual - Page 33
Audyssey, Setup, Preparations, Perform
UPC - 883795001014
View all Denon 4310CI manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 33 highlights
Audyssey Auto Setup Preparations around items indicate the settings made upon purchase. STEP1 Preparation Perform the following settings if adjustments, etc., are required for the speaker environment you're using. If you do not need to perform the following settings, or have already completed them, select "Auto Setup Start" and then press ENTER. Proceed to " STEP2 ". Change the Amplifier Assignment (Amp Assign) Set the Channels You will not Use (Channel Skip) The signal output from the SURR.BACK/AMP ASSIGN speaker terminal of the AVR-4310C1 can be switched to match your speaker environment ([26- page 34 "Amp Assign"). Select "Amp Assign" I and then ENTER. press AUDVSSEY AUTO SETUP IDENON 2 3 4 5 6 Connect the ...Oars and olece them according to the tecemmendatmne n the menus, Set the follow,. items If you set the channels you will not use beforehand, those channels will not be measured. Therefore, you can save an amount of time commensurate with that which would have been taken to measure those channels. I Select "Channel li elli.AUDYSSEV AUTO SETUP= DENON Skip" and then press STEPI hreeratleo M2 3 4 5 6 ENTER. Connect the speakers and place thorn according to the recommendations o6 the manual. Set the followIne items nesessare. Igl Perform Audyssey Auto Setup • Audyssey Auto Setup detects the presence of each speaker and automatically calculates the speaker size, channel level, distance and crossover frequency settings. In addition, acoustical distortions are corrected within the listening area. • When measuring begins, a test tone is output from each speaker. • Position and connect all speakers before commencing Audyssey Auto Setup. STEP2 Speaker Detection 1Select"Measure" and then press ENTER. .AUOVSSEY AUTO SETUP SE Pleese connect microphone. qi DENON (2} 3 4 56 (I) Measure the subwoofer level * To stop measuring, select "Cancel" and then press ONE ENTER. Make 0,SSItitt g • 2 Press A V to select an item, and then press ENTER. Normal : Outputs surround back channel audio. ZONE2 : Outputs ZONE2 audio. ZONE3 : Outputs ZONE3 audio. ZONE (MONO) : Outputs ZONE2 / ZONE3 monaural audio. Bi-Amp : Outputs front channel audio for bi-amp use. 2CH :Outputs front channel audio during 2-channel DIRECT and STEREO mode. Front Height : Outputs front height channel audio. Front Wide : Outputs front wide channel audio. *To cancel, press RETURN. channel: 2 Press 0 V to select a channel, press .1 L' to select the item, and then press ENTER. u Configurable channels Subwoofer : Set the subwoofer channel. Surround B Set the surround B channel. Surround Back : Set the surround back channel. u Settings Measure Default setting. Measure the selected channel. Skip Skip the selected channel and do not measure. To cancel, press RETURN. • When you are using surround back speakers with ZONE2/ZONE3, set to "ZONE2" or "ZONE3". • You can set in the same way as described in "Amp Assign" on page 34. 4'" When "Amp Assign" is set to "Normal", only then is "Surround Back" displayed. When "Subwoofer" is set to "Skip" with "Channel Skip", this measurement is not taken, and the process proceeds to "® Measure each speaker". ® Measure each speaker * Once the measurements in step are complete, the measurements in step ® start automatically. * The measuring channel changes depending on the setting of "Amp Assign" (trapage 30) and "Channel Skip" la?rpage 30). When an error message is displayed, check "Error Messages" for details (RZT'page 32). C) Check the speaker detection results When measuring ends, the speaker detection results are displayed. * Select "Next -> Measurement" and press ENTER to proceed to STEP3 * Press A to select "Retry", and when you press ENTER, measuring at the main listening position starts again. NOTE Since "Amp Assign" of AVR-4310CI is set to "ZONE2" by default, audio is not output from the surround back speakers. When using the surround back speakers with MAIN ZONE, change the "Amp Assign" setting to "Normal". Main remote control operation buttons SEARCH :Displaying the menu ENu Cancel the menu :Moves the cursor (Up/Down/Left/Right) ENTER :Confirm the setting :Return to previous menu 30