Denon 4310CI Owners Manual - Page 39
Denon 4310CI - AVR AV Network Receiver Manual
UPC - 883795001014
View all Denon 4310CI manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 39 highlights
Setting items Distance (Continued) Setting contents Front L / Front R / Center / Subwoofer / Surround A L / Surround A R / Surround B L / Surround B R / Surr. Back L* / Surr. Back R * / Front Height L / Front Height R / Front Wide L / Front Wide R : Select the speaker. *: When the "Speaker Configuration" - "Surround Back" setting (0- page 35) is set to "lspkr", "Surr. Back" is displayed. • 0.0ft - 60.0ft / 0.00m - 18.00m : Set the distance. • Speakers set to "None" in "Speaker Configuration" ( page 34) are not displayed. • The speakers that can be selected differ depending on the "Amp Assign" (o-page 34) and "Speaker Configuration" Vrpage 34) settings. • Default settings : Front / Center / Subwoofer / Front Height / Front Wide : 12.0 ft (3.60 m) Surround A / Surround B / Surround Back : 10.0 ft (3.00 m) • Set the difference in the distance between the speakers to less than 20 feet (6.0 meters). Channel Level Surround Speaker : Set the surround speakers to output the test tone. Set the volume of the test • A : Output test tone from surround speakers A. tone to be the same when it • B : Output test tone from surround speakers B. is output from each speaker. • A+B : Output test tone from surround speakers A and B. ,00- Can be set when the "Speaker Configuration" - "Surround A" or "Surround B" setting is "Large" or "Small" (tCFpage 35). Test Tone : Output test tone. • Front L / Front Height L / Center / Front Height R / Front R / Front Wide R / Surround R /Surr. Back R * /Surr. Back L* / Surround L / Front Wide L / Subwoofer : Select the speaker. * : When the "Speaker Configuration" - "Surround Back" setting to page 35) is set to "lspkr", "Surr. Back" is displayed. • -12dB - +12dB (0dB) : Adjust the volume. • Speakers set to "None" in the "Speaker Configuration" (¢2r page 34) settings are not displayed. • When < is pressed while the subwoofer volume is set to "-12 dB", the "Subwoofer" setting switches to "OFF". • When using surround speakers, be sure to adjust the volume of the different speakers. • When a headphones jack is inserted in the PHONES terminal of the AVR4310C1, the "Channel Level" is not displayed. • You can also press CHANNEL LEVEL to set (Crpage 81 "Adjust the Volume of the Different Speakers"). Default : Reset all channel level settings to factory default. • Yes : Reset to the defaults. • No : Do not reset to the defaults. Making Detailed Settings {Manual Setup) Setting items Setting contents Crossover Frequency 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz / Outputs at below set 250Hz : Set the crossover frequency. frequency, each speaker's bass signal output from the subwoofer. Set this Advanced : Specify crossover frequency for each speaker. • Front / Center / Surround A / Surround B / Surround A+B / Surround Back / Front Height / Front Wide : Select the speaker. according to the low • 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz /150Hz / 200Hz / frequency reproduction 250Hz : Set the crossover frequency. capabilities of the speakers you are using. 40" • Can be set when the "Speaker Configuration" - "Subwoofer" (a2r page 34) setting is "Yes", or when you have a speaker that is set to "Small". • Always set the crossover frequency to "80Hz". When using small speakers, however, we recommend setting the crossover frequency to a higher frequency. • For speakers set to "Small", sound below the crossover frequency is cut from the sound output. The cut bass sound is output from the subvvoofer or front speakers. • The speakers that can be set when "Advanced" is selected differ according to the "Subwoofer Mode" setting VFpage 35). • When "LFE" is selected, speakers set to "Small" at "Speaker Configuration" can be set. If the speakers are set to "Large", "Full Band" is displayed and the setting cannot be made. • If set to "LFE+Main", this setting can be made regardless of the speaker size. Surround Speaker DOLBY/DTS Cinema : Set the surround speakers to use during Dolby/ Set the surround speakers DTS Cinema mode. to use for every surround DOLBY/DTS Music : Set the surround speakers to use during Dolby/DTS mode. Music mode. DOLBY Game : Set the surround speakers to use during Dolby Game mode. DOLBY Height : Set the surround speakers to use during Dolby Height mode. WIDE SCREEN : Set the surround speakers to use during WIDE SCREEN mode. 7CH STEREO : Set the surround speakers to use during 7CH STEREO mode. DSP SIMULATION : Set the surround speakers to use during the DENON original surround mode. MULTI CH MODE : Set the surround speakers to use during PCM or DSD multi-channel mode. • A : Use surround speakers A. • B : Use surround speakers B. • A+B : Use surround speakers A and B. "Surround Speaker" is displayed when "Speaker Configuration" - "Surround A" and "Surround B" setting (IC - page 35) is set to "Large" or "Small". See overleaf > Main remote control operation buttons SEARCH :Displaying the menu Exu Cancel the menu