Epson ActionTower 7500 User Manual - Page 110

Reconnecting the Cables to the Diskette Drive

Get Epson ActionTower 7500 PDF manuals and user guides View all Epson ActionTower 7500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 110 highlights

Reconnecting the Cables to the Diskette Drive Refer to the illustration below while you follow these steps: 1. Locate the connector on the diskette drive ribbon cable. 2. Identify pin 1 on the drive and align the connector so that the red wire is at pin 1. Push in the connector. 3. Locate the power supply cable with the small connector. 4. Position the power supply cable connector so that the holes fit over all the pins and the red wire aligns with pin 1 on the drive's connector. Then push in the connector. 5. If you have finished installing or removing drives, replace the computer's cover, as described under "Replacing the Cover" in Chapter 4. Then see "Using the Fixed Disk getup Option" in Chapter 2 for instructions on defining your new drive configuration. 5-12 Installing and Removing Slimline Drives

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
Reconnecting the Cables to the Diskette Drive
Refer to the illustration below while you follow these steps:
1.
2.
3.
4.
5.
Locate the connector on the diskette drive ribbon cable.
Identify pin 1 on the drive and align the connector so that
the red wire is at pin 1. Push in the connector.
Locate the power supply cable with the small connector.
Position the power supply cable connector so that the holes
fit over all the pins and the red wire aligns with pin 1 on
the drive’s connector. Then push in the connector.
If you have finished installing or removing drives, replace
the computer’s cover, as described under “Replacing the
Cover” in Chapter 4. Then see “Using the Fixed Disk getup
Option” in Chapter 2 for instructions on defining your new
drive configuration.
5-12
Installing and Removing Slimline Drives