Epson ActionTower 7500 User Manual - Page 27

Connecting the Power Cord, If you use ECP mode Extended Capabilities Port, check

Get Epson ActionTower 7500 PDF manuals and user guides View all Epson ActionTower 7500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Note If you use ECP mode (Extended Capabilities Port), check your parallel device software documentation for the correct DMA channel (DRQ) setting. Then set jumpers JP8 and JP18 to match this setting if necessary. See "Changing the Jumper Settings" in Chapter 4 for more information. Using the serial ports If you have a printer, a modem, or other device with a serial interface, you can connect it to one of the serial (RS-232C) ports. Make sure you have a cable compatible with a DB-9P connector. To connect a serial device, insert the connector into either of the two serial ports, which are marked with l o the icons shown at the left. If you are connecting only one serial device, use the serial 1 port. Connecting the Power Cord Follow these steps to connect the computer's power cord: 1. Plug the power cord into the power inlet on the back of the computer. Note that the position of the power inlet and AC outlet on your computer may be reversed. Setting Up Your System 1-7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
Note
If you use ECP mode (Extended Capabilities Port), check
your parallel device software documentation for the correct
DMA channel (DRQ) setting. Then set jumpers JP8 and JP18
to match this setting if necessary. See “Changing the Jumper
Settings” in Chapter 4 for more information.
Using the serial ports
If you have a printer, a modem, or other device with a serial
interface, you can connect it to one of the serial (RS-232C) ports.
Make sure you have a cable compatible with a DB-9P connector.
To connect a serial device, insert the connector into
l
o
either of the two serial ports, which are marked with
the icons shown at the left. If you are connecting only
one serial device, use the serial 1 port.
Connecting the Power Cord
Follow these steps to connect the computer’s power cord:
1.
Plug the power cord into the power inlet on the back of the
computer. Note that the position of the power inlet and AC
outlet on your computer may be reversed.
Setting Up Your System
1-7