Epson ActionTower 7500 User Manual - Page 75

Setting the Jumpers, placed on the pins. Use the table below to identify the pin

Get Epson ActionTower 7500 PDF manuals and user guides View all Epson ActionTower 7500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 75 highlights

Setting the Jumpers To change a jumper setting, follow these steps: 1. Refer to the illustration under "Locating System Board Components" to locate the jumpers. 2. If any option cards are installed in your computer, you may need to remove them to access the jumpers. See "Removing an Option Card" for instructions. 3. A jumper's setting is determined by where the jumper is placed on the pins. Use the table below to identify the pin settings for 2-, 3-, and 4-pin jumpers. (To identify the pin numbers, look at the system board under the jumper.) For 6-pin jumpers, refer to the 4-pin illustrations and set jumpers accordingly. 4-12 Installing and Removing Options

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
Setting the Jumpers
To change a jumper setting, follow these steps:
1.
Refer to the illustration under “Locating System Board
Components” to locate the jumpers.
2.
If any option cards are installed in your computer, you
may need to remove them to access the jumpers. See
“Removing an Option Card” for instructions.
3.
A jumper’s setting is determined by where the jumper is
placed on the pins. Use the table below to identify the pin
settings for 2-, 3-, and 4-pin jumpers. (To identify the pin
numbers, look at the system board under the jumper.)
For 6-pin jumpers, refer to the 4-pin illustrations and set
jumpers accordingly.
4-12
Installing and Removing Options