Epson ActionTower 7500 User Manual - Page 138

Installing a Drive in the Rear Internal Bracket

Get Epson ActionTower 7500 PDF manuals and user guides View all Epson ActionTower 7500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 138 highlights

4. If you removed the only IDE device connected to the interface the device used, you may want to disconnect the device cable from the interface on the main system board and remove it from the computer. 5. If you have finished installing or removing drives, replace the computer's cover, as described under "Replacing the Cover" in Chapter 4. Then see "Using the Fixed Disk Setup 0ption" in Chapter 2 for instructions on defining your new drive configuration. Installing a Drive in the Rear Internal Bracket Your computer has a hard disk drive installed in the rear internal drive bracket. Follow these steps to install a second drive in this bracket: 1. Remove the drive and power cables from the back of any drive already installed in the rear internal drive bracket. 2. Remove the four screws securing the rear internal drive bracket to the computer's back panel and slide it out of the computer. Make sure you save the screws. Installing and Removing Tower Drives 6-17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
4.
If you removed the only IDE device connected to the
interface the device used, you may want to disconnect the
device cable from the interface on the main system board
and remove it from the computer.
5.
If you have finished installing or removing drives, replace
the computer’s cover, as described under “Replacing the
Cover” in Chapter 4. Then see “Using the Fixed Disk Setup
0ption” in Chapter 2 for instructions on defining your new
drive
configuration.
Installing a Drive in the Rear Internal Bracket
Your computer has a hard disk drive installed in the rear
internal drive bracket. Follow these steps to install a second
drive in this bracket:
1.
Remove the drive and power cables from the back of any
drive already installed in the rear internal drive bracket.
2.
Remove the four screws securing the rear internal drive
bracket to the computer’s back panel and slide it out of the
computer. Make sure you save the screws.
Installing and Removing Tower Drives
6-17