Epson C823622 Administrator's Manual - Page 89

Configuring the Ethernet Card Using EPSON Net!2 for Macintosh, EPSON Net!2, Configuration

Get Epson C823622 PDF manuals and user guides View all Epson C823622 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 89 highlights

Configuring the Ethernet Card Using EPSON Net!2 for Macintosh Use EPSON Net!2 for Macintosh to configure the Ethernet card as described below. c Caution: Once you make changes to the Ethernet card using EPSON Net!2, wait until it registers the settings before turning off or sending data to the printer. 1. Make AppleTalk active in the Chooser. 2. Connect the Ethernet card to the network and turn on the printer. 3. From your hard disk, double-click the EPSON Net!2 icon. 4. Highlight the printer you want to configure from the list and click Configuration. Note: u If you have connected more than one printer with the same type of Ethernet card to the network, you can distinguish the cards by their MAC (Media Access Control) addresses. To view a card's MAC address, press the status sheet button on the card for three seconds. See Chapter 1 for details. u If the IP address is set to the default IP address, the printer model might not appear. Using the Ethernet Card with Macintosh 5-3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
Using the Ethernet Card with Macintosh
5-3
Configuring the Ethernet Card Using EPSON Net!2 for
Macintosh
Use EPSON Net!2 for Macintosh to configure the Ethernet card as
described below.
c
Caution:
Once you make changes to the Ethernet card using EPSON Net!2,
wait until it registers the settings before turning off or sending data
to the printer.
1.
Make AppleTalk active in the Chooser.
2.
Connect the Ethernet card to the network and turn on the
printer.
3.
From your hard disk, double-click the
EPSON Net!2
icon.
4.
Highlight the printer you want to configure from the list and
click
Configuration
.
Note:
If you have connected more than one printer with the same type of
Ethernet card to the network, you can distinguish the cards by
their MAC (Media Access Control) addresses. To view a card’s
MAC address, press the status sheet button on the card for three
seconds. See Chapter 1 for details.
If the IP address is set to the default IP address, the printer model
might not appear.