Fluke 8808A User Manual - Page 33

Cleaning the Meter, Fluke 45 Emulation, to the Meter.

Get Fluke 8808A PDF manuals and user guides View all Fluke 8808A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

2 Preparing the Meter for Operation Cleaning the Meter To prepare the Meter for rack mounting, remove the bail and remove the front and rear protective boots. To remove a boot, stretch a corner then slide it off as shown in Figure 25. To install the Meter into the rack, refer to the instructions provided with the Rack Mount Kit. Figure 2-5. Boot Removal eue22.eps Cleaning the Meter XW Warning To avoid electric shock or damage to the Meter, never get water inside the Meter. W Caution To avoid damaging the Meter's housing, do not apply solvents to the Meter. If the Meter requires cleaning, wipe it down with a cloth that is lightly dampened with water or a mild detergent. Do not use aromatic hydrocarbons, alchohol, chlorinated solvents, or methanol-based fluids when wiping down the Meter. Fluke 45 Emulation To switch the Meter to Fluke 45 emulation: Press and hold Sand f for two seconds. 2-9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
Preparing the Meter for Operation
Cleaning the Meter
2
2-9
To prepare the Meter for rack mounting, remove the bail and remove the front and rear
protective boots. To remove a boot, stretch a corner then slide it off as shown in Figure 2-
5.
To install the Meter into the rack, refer to the instructions provided with the Rack Mount
Kit.
eue22.eps
Figure 2-5. Boot Removal
Cleaning the Meter
XW
Warning
To avoid electric shock or damage to the Meter, never get water
inside the Meter.
W
Caution
To avoid damaging the Meter’s housing, do not apply solvents
to the Meter.
If the Meter requires cleaning, wipe it down with a cloth that is lightly dampened with
water or a mild detergent. Do not use aromatic hydrocarbons, alchohol, chlorinated
solvents, or methanol-based fluids when wiping down the Meter.
Fluke 45 Emulation
To switch the Meter to Fluke 45 emulation:
Press and hold
S
and
f
for two seconds.