Fluke 8808A User Manual - Page 54

Minimum / Maximum Modifier (MIN MAX), is first pressed, the minimum and maximum values are set to

Get Fluke 8808A PDF manuals and user guides View all Fluke 8808A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

8808A Users Manual • Level 1 (0.01 % of reading) • Level 2 (0.1 % of reading) • Level 3 (1 % of reading) • Level 4 (10 % of reading) To change the response level, press Q and I. The response level currently selected (1, 2, 3 or 4) appears on the primary display. Press U or V to step to the desired response level, then press R for two seconds to set the level and return to the primary display. You can return to the primary display without changing the response level by pressing any button except R, U or V. Minimum / Maximum Modifier (MIN MAX) The minimum/maximum (MIN MAX) modifier stores the minimum and maximum inputs of your measurements. Selecting the MIN MAX modifier turns off autoranging and locks in the present range, so make sure you are in the correct range before pressing N. If you press U or V after pressing N, the Meter exits the MIN MAX modifier mode. To store the minimum and maximum inputs: 1. Press N to select the MIN MAX modifier. When N is first pressed, the minimum and maximum values are set to the reading displayed. MAX is shown and the display indicates the latest maximum reading. 2. Press N again to display the minimum reading. MIN is shown and the display indicates the latest minimum reading. 3. Press N again to display either the minimum or maximum reading. M is shown and the display indicates either the minimum or maximum reading. 4. To exit MIN MAX mode, press and hold N for 2 seconds. 5. To observe the actual readings without resetting the stored values, press Q and then select the same measurement function that you selected for the primary display. 3-20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
8808A
Users Manual
3-20
•
Level 1 (0.01 % of reading)
•
Level 2 (0.1 % of reading)
•
Level 3 (1 % of reading)
•
Level 4 (10 % of reading)
To change the response level, press
Q
and
I
. The response level currently selected
(1, 2, 3 or 4) appears on the primary display. Press
U
or
V
to step to the desired
response level, then press
R
for two seconds to set the level and return to the primary
display. You can return to the primary display without changing the response level by
pressing any button
except
R
,
U
or
V
.
Minimum / Maximum Modifier (MIN MAX)
The minimum/maximum (MIN MAX) modifier stores the minimum and maximum
inputs of your measurements.
Selecting the MIN MAX modifier turns off autoranging and locks in the present range, so
make sure you are in the correct range before pressing
N
. If you press
U
or
V
after pressing
N
, the Meter exits the MIN MAX modifier mode.
To store the minimum and maximum inputs:
1.
Press
N
to select the MIN MAX modifier.
When
N
is first pressed, the minimum and maximum values are set to the
reading displayed.
MAX
is shown and the display indicates the latest maximum
reading.
2.
Press
N
again to display the minimum reading.
MIN
is shown and the display
indicates the latest minimum reading.
3.
Press
N
again to display either the minimum or maximum reading.
M
is shown and the display indicates either the minimum or maximum reading.
4.
To exit MIN MAX mode, press and hold
N
for 2 seconds.
5.
To observe the actual readings without resetting the stored values, press
Q
and
then select the same measurement function that you selected for the primary
display.