HP 4410t HP 4410t Mobile Thin Client - Page 65

Connecting to a local area network

Get HP 4410t - Mobile Thin Client PDF manuals and user guides
UPC - 884962419915
View all HP 4410t manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

Dial a telephone number, make sure there is a response from the remote modem, and then hang up. ● Set the modem to ignore dial tones. If the modem receives a dial tone it does not recognize, it does not dial and displays a "No Dial Tone" error message. To set the modem to ignore all dial tones before dialing, follow these steps: 1. Select Start > Control Panel > Printers and Other Hardware > Phone and Modem Options. 2. Then click the Modems tab. 3. Click the listing for the modem. 4. Click Properties. 5. Click Modem. 6. Clear the check box for Wait for dial tone before dialing. 7. Click OK twice. NOTE: You must commit these changes in order for them to be saved. Refer to Chapter 2, "HP Write Filters," for additional information. Connecting to a local area network Connecting to a local area network (LAN) requires an 8-pin, RJ-45 network cable (purchased separately). If the network cable contains noise suppression circuitry (1), which prevents interference from TV and radio reception, orient the circuitry end of the cable (2) toward the computer. To connect the network cable: 1. Connect the network cable into the network jack (1) on the computer. Connecting to a local area network 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
Dial a telephone number, make sure there is a response from the remote modem, and then hang
up.
●
Set the modem to ignore dial tones.
If the modem receives a dial tone it does not recognize, it does not dial and displays a “No Dial
Tone” error message.
To set the modem to ignore all dial tones before dialing, follow these steps:
1.
Select
Start
>
Control Panel
>
Printers and Other Hardware
>
Phone and Modem
Options
.
2.
Then click the
Modems
tab.
3.
Click the listing for the modem.
4.
Click
Properties
.
5.
Click
Modem
.
6.
Clear the check box for
Wait for dial tone before dialing
.
7.
Click
OK
twice.
NOTE:
You must commit these changes in order for them to be saved. Refer to Chapter 2, “HP
Write Filters,” for additional information.
Connecting to a local area network
Connecting to a local area network (LAN) requires an 8-pin, RJ-45 network cable (purchased
separately). If the network cable contains noise suppression circuitry
(1)
, which prevents interference
from TV and radio reception, orient the circuitry end of the cable
(2)
toward the computer.
To connect the network cable:
1.
Connect the network cable into the network jack
(1)
on the computer.
Connecting to a local area network
55