HP BladeSystem c3000 HP BladeSystem c-Class Enclosure Troubleshooting Guide - Page 46

Verification, Step 7, Action, Static OA1 IP settings, DHCP OA IP settings, New OA1 IP address

Get HP BladeSystem c3000 PDF manuals and user guides View all HP BladeSystem c3000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Step Step 7 Step 8 Step 9 Onboard Administrator errors action and verification Verification Wait until the Insight Display indicates that the second or non-suspect Onboard Administrator has completed power-on tests. If the second or non-suspect HP BladeSystem c3000 OA operates properly, then replace the suspect Onboard Administrator and continue with step 9. If the second or non-suspect OA has the same issue as the suspect OA, and the suspect OA is OA1, then continue to the next step. Action Reseat the OA tray: 1 Remove all Onboard Administrators from the OA tray. 2 Reseat the OA tray. 3 Install all Onboard Administrators in their original locations. Verification Wait until the Insight Display indicates that the Onboard Administrators have completed power-on tests. If the active Onboard Administrator operates properly, then the repair is complete. If the active Onboard Administrator symptoms still exist, then replace the OA tray and continue to step 9. Action Contact an HP authorized service provider to complete the midplane assembly replacement (on page 66). Action Obtain the OA1 IP settings from the enclosure administrator. Static OA1 IP settings: 1 Use the Insight Display Enclosure Settings information to change the OA1 IP address to static. 2 Enter the following information recorded in the previous step: -IP address -Netmask -Gateway 3 Record or tear off the replaced Onboard Administrator password from the label on the OA tray. DHCP OA IP settings: 1 Use the Insight Display Enclosure Settings information to change the OA1 IP address to DHCP. 2 Record the following information: -New OA1 IP address -DNS name of the old Onboard Administrator from the label -DNS name of the new Onboard Administrator from the label 3 Record or tear off the replaced Onboard Administrator password from the label on the OA tray. Enclosure troubleshooting 46

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
Enclosure troubleshooting 46
Step
Onboard Administrator errors action and verification
Verification
Wait until the Insight Display indicates that the second or non-suspect Onboard
Administrator has completed power-on tests.
If the second or non-suspect HP BladeSystem c3000 OA operates properly, then replace
the suspect Onboard Administrator and continue with step 9.
If the second or non-suspect OA has the same issue as the suspect OA, and the suspect OA
is OA1, then continue to the next step.
Step 7
Action
Reseat the OA tray:
1
Remove all Onboard Administrators from the OA tray.
2
Reseat the OA tray.
3
Install all Onboard Administrators in their original locations.
Verification
Wait until the Insight Display indicates that the Onboard Administrators have completed
power-on tests.
If the active Onboard Administrator operates properly, then the repair is complete.
If the active Onboard Administrator symptoms still exist, then replace the OA tray and
continue to step 9.
Step 8
Action
Contact an HP authorized service provider to complete the midplane assembly
replacement (on page
66
).
Step 9
Action
Obtain the OA1 IP settings from the enclosure administrator.
Static OA1 IP settings
:
1
Use the Insight Display Enclosure Settings information to change the OA1 IP address to
static.
2
Enter the following information recorded in the previous step:
-IP address
-Netmask
-Gateway
3
Record or tear off the replaced Onboard Administrator password from the label on the
OA tray.
DHCP OA IP settings
:
1
Use the Insight Display Enclosure Settings information to change the OA1 IP address to
DHCP.
2
Record the following information:
-New OA1 IP address
-DNS name of the old Onboard Administrator from the label
-DNS name of the new Onboard Administrator from the label
3
Record or tear off the replaced Onboard Administrator password from the label on the
OA tray.