HP BladeSystem c3000 HP BladeSystem c-Class Enclosure Troubleshooting Guide - Page 56

KVM troubleshooting, Symptoms: c3000 enclosure KVM errors

Get HP BladeSystem c3000 PDF manuals and user guides View all HP BladeSystem c3000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

Step Step 7 External DVD-ROM troubleshooting action and verification Action Test the OA module connection: 1 Reseat the OA module. 2 Wait for OA to reboot. 3 Navigate to the Insight Display Health Summary screen. 4 Verify the DVD-ROM drive status. Verification If the DVD-ROM drive status is gray or green, then the repair is complete. If the DVD-ROM drive status is black, continue to step 1 of "Onboard Administrator troubleshooting (on page 43)." KVM troubleshooting For KVM module information, see the KVM module documentation. For specific component LED definitions and component identification, see "Component identification (on page 73)." Symptoms: c3000 enclosure KVM errors The procedures in this section assume that the firmware for Onboard Administrator, iLO 2, and BIOS is updated to the newest versions available. Always verify firmware versions before continuing with the steps in this section. If the c3000 enclosure KVM module is connected to an external rack KVM switch, where pressing "Print Screen" is indicated, then press Print Screen twice to select the Enclosure KVM menu. The first press of Print Screen opens the rack KVM Switch Port Selection menu. On some c3000 enclosures, the user can set only one of the following as active: • The USB connector on the front of the enclosure and the internal DVD-ROM drive. • The rear USB connectors on the KVM module. On these enclosures, in order to use the both the KVM and the internal DVD-ROM drive, always connect the KVM keyboard and mouse to the front USB connector on the OA. Symptom Initial step Required steps Pressing the KVM keyboard Print Screen key does not bring up the Enclosure KVM Menu. Be sure that the KVM monitor is Begin with step 1 of "Procedures: powered up and is connected to the KVM Menu troubleshooting (on page KVM module VGA connector. Be sure 58)." that the KVM keyboard/mouse are connected to the KVM module USB connectors. The KVM Menu button does not - appear on the navigation bar at the bottom of the Insight Display Begin with step 1 of "Procedures: KVM module troubleshooting (on page 60)." Main Menu. When typing on Linux virtual - console through KVM, multiple characters appear. Begin with step 1 of "Procedures: KVM Linux troubleshooting (on page 60)." Enclosure troubleshooting 56

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
Enclosure troubleshooting 56
Step
External DVD-ROM troubleshooting action and verification
Step 7
Action
Test the OA module connection:
1
Reseat the OA module.
2
Wait for OA to reboot.
3
Navigate to the Insight Display Health Summary screen.
4
Verify the DVD-ROM drive status.
Verification
If the DVD-ROM drive status is gray or green, then the repair is complete.
If the DVD-ROM drive status is black, continue to step 1 of "Onboard Administrator
troubleshooting (on page
43
)."
KVM troubleshooting
For KVM module information, see the KVM module documentation.
For specific component LED definitions and component identification, see "Component identification (on
page
73
)."
Symptoms: c3000 enclosure KVM errors
The procedures in this section assume that the firmware for Onboard Administrator, iLO 2, and BIOS is
updated to the newest versions available. Always verify firmware versions before continuing with the steps
in this section.
If the c3000 enclosure KVM module is connected to an external rack KVM switch, where pressing "Print
Screen" is indicated, then press
Print Screen
twice to select the Enclosure KVM menu. The first press of
Print
Screen
opens the rack KVM Switch Port Selection menu.
On some c3000 enclosures, the user can set only one of the following as active:
•
The USB connector on the front of the enclosure and the internal DVD-ROM drive.
•
The rear USB connectors on the KVM module.
On these enclosures, in order to use the both the KVM and the internal DVD-ROM drive, always connect the
KVM keyboard and mouse to the front USB connector on the OA.
Symptom
Initial step
Required steps
Pressing the KVM keyboard
Print Screen
key does not bring
up the Enclosure KVM Menu.
Be sure that the KVM monitor is
powered up and is connected to the
KVM module VGA connector. Be sure
that the KVM keyboard/mouse are
connected to the KVM module USB
connectors.
Begin with step 1 of "Procedures:
KVM Menu troubleshooting (on page
58
)."
The KVM Menu button does not
appear on the navigation bar at
the bottom of the Insight Display
Main Menu.
—
Begin with step 1 of "Procedures:
KVM module troubleshooting (on
page
60
)."
When typing on Linux virtual
console through KVM, multiple
characters appear.
—
Begin with step 1 of "Procedures:
KVM Linux troubleshooting (on page
60
)."