HP DL785 HP ProLiant DL785 G5 and G6 Servers - Maintenance and Service Guide, - Page 37

SAS hard drive blank, To remove a SAS hard drive

Get HP DL785 - ProLiant - G5 PDF manuals and user guides
UPC - 883585262809
View all HP DL785 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

SAS hard drive blank To remove a SAS hard drive blank: 1. Squeeze the tabs on the front of the filler to release it from the slot in the drive bay. 2. Pull gently until the filler slides out of the chassis. SAS hard drives CAUTION: Always power down the server if the boot partition resides on the drive you are replacing or if you are replacing the only drive in the server. CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless all bays are populated with either a component or a blank. To remove a SAS hard drive: 1. Determine the status of the hard drive from the hot-plug hard drive LEDs ("SAS and SATA hard drive LEDs" (page 66) and "SAS and SATA hard drive LED combinations" (page 66)). 2. Back up all data on the hard drive. 3. Remove the hard drive. SAS hard drive blank 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
SAS hard drive blank
To remove a SAS hard drive blank:
1.
Squeeze the tabs on the front of the filler to release it from the slot in the drive bay.
2.
Pull gently until the filler slides out of the chassis.
SAS hard drives
CAUTION:
Always power down the server if the boot partition resides on the drive you are
replacing or if you are replacing the only drive in the server.
CAUTION:
To prevent improper cooling and thermal damage, do not operate the server unless
all bays are populated with either a component or a blank.
To remove a SAS hard drive:
1.
Determine the status of the hard drive from the hot-plug hard drive LEDs (
“SAS and SATA
hard drive LEDs” (page 66)
and
“SAS and SATA hard drive LED combinations” (page 66)
).
2.
Back up all data on the hard drive.
3.
Remove the hard drive.
SAS hard drive blank
37