HP Designjet T620 HP Designjet T620 Printer Series - Users Guide - Page 102

the screw with the screwdriver in your other hand

Get HP Designjet T620 PDF manuals and user guides View all HP Designjet T620 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 102 highlights

10. Slide the new cutter into position on the cutter rail. The two wheels on the bottom of the cutter should engage the central ridge on the cutter rail, and the two bushing guides should fit into the groove in the upper part of the cutter rail. Check that the cutter runs smoothly up and down the rail. You can leave it anywhere on the rail; the printer will park it correctly later. 11. Fit the cutter stop onto the end of the cutter rail, holding it there with one hand while you tighten the screw with the screwdriver in your other hand. Printer maintenance ENWW Replace the cutter 99

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
10.
Slide the new cutter into position on the cutter rail.
The two wheels on the bottom of the cutter should engage the central ridge on the cutter rail, and
the two bushing guides should fit into the groove in the upper part of the cutter rail.
Check that the cutter runs smoothly up and down the rail. You can leave it anywhere on the rail;
the printer will park it correctly later.
11.
Fit the cutter stop onto the end of the cutter rail, holding it there with one hand while you tighten
the screw with the screwdriver in your other hand.
ENWW
Replace the cutter
99
Printer maintenance