HP EliteDesk 705 G2 Maintenance and Service Guide - Page 45

Installing a 9.5mm slim optical drive

Get HP EliteDesk 705 G2 PDF manuals and user guides View all HP EliteDesk 705 G2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Installing a 9.5mm slim optical drive 1. Prepare the computer for disassembly (Preparation for disassembly on page 19). 2. Remove the access panel (Access panel on page 20). 3. Remove the front bezel if you are installing a drive in a bay covered by a bezel blank, then remove the bezel blank. See Front bezel on page 20 for more information. 4. Align the small pin on the release latch with the small hole on the side of the drive and press the latch firmly onto the drive. 5. Slide the optical drive through the front of the chassis all the way into the bay so that it locks in place (1), and then connect the power cable (2) and data cable (3) to the rear of the drive. 6. Connect the opposite end of the data cable to one of the light blue SATA connectors on the system board. NOTE: Refer to System board connections on page 31 for an illustration of the system board drive connectors. Drives 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
Installing a 9.5mm slim optical drive
1.
Prepare the computer for disassembly (
Preparation for disassembly
on page
19
).
2.
Remove the access panel (
Access panel
on page
20
).
3.
Remove the front bezel if you are installing a drive in a bay covered by a bezel blank, then remove the
bezel blank. See
Front bezel
on page
20
for more information.
4.
Align the small pin on the release latch with the small hole on the side of the drive and press the latch
firmly
onto the drive.
5.
Slide the optical drive through the front of the chassis all the way into the bay so that it locks in place
(1), and then connect the power cable (2) and data cable (3) to the rear of the drive.
6.
Connect the opposite end of the data cable to one of the light blue SATA connectors on the system
board.
NOTE:
Refer to
System board connections
on page
31
for an illustration of the system board drive
connectors.
Drives
35