HP EliteDesk 705 G2 Maintenance and Service Guide - Page 61

Front I/O assembly, Remove the Torx T15 screw

Get HP EliteDesk 705 G2 PDF manuals and user guides View all HP EliteDesk 705 G2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

Front I/O assembly The front I/O assembly is attached to the front of the chassis with one screw. Push the assembly into the chassis to remove. 1. Prepare the computer for disassembly (Preparation for disassembly on page 19). 2. Remove the access panel (Access panel on page 20). 3. Remove the front bezel (Front bezel on page 20). 4. Rotate the drive cage to its upright position. 5. Disconnect the cables from the system board as follows: (1) Yellow connector labeled FRONT_USB (2) Blue connector labeled FRONT AUD (3) Blue connector labeled FRONT_USB3.0 6. Remove the cables from the three clips built into the basepan (4). 7. Remove the Torx T15 screw (1) that secures the assembly to the front of the chassis. Front I/O assembly 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
Front I/O assembly
The front I/O assembly is attached to the front of the chassis with one screw. Push the assembly into the
chassis to remove.
1.
Prepare the computer for disassembly (
Preparation for disassembly
on page
19
).
2.
Remove the access panel (
Access panel
on page
20
).
3.
Remove the front bezel (
Front bezel
on page
20
).
4.
Rotate the drive cage to its upright position.
5.
Disconnect the cables from the system board as follows:
(1)
Yellow connector labeled FRONT_USB
(2)
Blue connector labeled FRONT AUD
(3)
Blue connector labeled FRONT_USB3.0
6.
Remove the cables from the three clips built into the basepan
(4)
.
7.
Remove the Torx T15 screw
(1)
that secures the assembly to the front of the chassis.
Front I/O assembly
51