HP EliteOne 800 Maintenance & Service Guide HP EliteOne 800 G1 All-in-One - Page 100

Updating the display panel manufacturer setting in BIOS, LVDS Panel Select - bios settings

Get HP EliteOne 800 PDF manuals and user guides View all HP EliteOne 800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 100 highlights

16. Slide the system board toward the top of the computer, and then lift it out of the computer. To install the system board, reverse the removal procedures. Replace the thermal pad below the system board. Updating the display panel manufacturer setting in BIOS After replacing the system board, make sure the display panel manufacturer setting is correct in BIOS. If the incorrect panel manufacturer is set in BIOS, the display panel may function incorrectly. The display panel manufacturer is identified on the jumper setting label on the base pan. After confirming the manufacturer of the display panel on the computer, go into BIOS and make sure the LVDS Panel Select setting is correct. To update BIOS with display panel model information: 1. Boot the computer. 2. Repeatedly press F10 when the monitor light turns green to access the F10 Setup utility. 90 Chapter 5 Removal and Replacement Procedures All-in One (AIO) Chassis

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
16.
Slide the system board toward the top of the computer, and then lift it out of the computer.
To install the system board, reverse the removal procedures.
Replace the thermal pad below the system board.
Updating the display panel manufacturer setting in BIOS
After replacing the system board, make sure the display panel manufacturer setting is correct in BIOS. If
the incorrect panel manufacturer is set in BIOS, the display panel may function incorrectly.
The display panel manufacturer is identified on the jumper setting label on the base pan.
After confirming the manufacturer of the display panel on the computer, go into BIOS and make sure
the
LVDS Panel Select
setting is correct.
To update BIOS with display panel model information:
1.
Boot the computer.
2.
Repeatedly press
F10
when the monitor light turns green to access the F10 Setup utility.
90
Chapter 5
Removal and Replacement Procedures All-in One (AIO) Chassis