HP Integrity Superdome SX2000 HP Integrity Servers with Microsoft Windows Serv - Page 38

Post-Installation Tasks, Tips and Tricks

Get HP Integrity Superdome SX2000 PDF manuals and user guides View all HP Integrity Superdome SX2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

2. If you choose to install from a GUI console you are prompted to specify server settings when the Windows setup is complete. Post-Installation Tasks Perform the following tasks in the order shown. The operating system must be installed before performing these tasks : 1. Apply the operating system and security updates from the HP Smart Update DVD. 2. Install the HP Support Pack from the HP Smart Setup CD to update firmware and device drivers. 3. Install updates from the HP website. 4. Enable Windows Components. a. Install TCP/IP. b. Install SNMP. c. Configure SNMP. 5. Install Management Tools. a. Install Partition Management tools. b. Install System Management Homepage. c. Install Management Agents. Tips and Tricks The following tips enable you to overcome some issues you might encounter while deploying your Integrity server. • Install Service Pack 2 This upgrade is necessary for Intel Dual Core Itanium processor support. • Enable hyper-threading on Integrity servers The default setting for hyper-threading is off. To enable hyper-threading, go to the EFI shell and enter cpuconfig threads on. To disable hyper-threading, go to the EFI shell and enter cpuconfig threads off. • Enable remote desktop connection from a headless server The remote administration mode is enabled by default on Windows Server 2003 if you are using the operating system supplied as part of the HP reinstall media. If you are installing or reinstalling using Microsoft RTM media, the Remote Desktop functionality is disabled. To enable remote desktop connections, the following WMIC command: WMIC RdToggle WHERE AllowTSConnections=0 CALL SetAllowTSConnections 1 To enable remote desktop traffic through the Windows Firewall, enter: netsh firewall set service remotedesktop enable all • Enable greater than 256 interrupts (cell-based servers only) When using Windows Server 2003 on cell-based servers, the system only allows 256 interrupts. To overcome this limitation, apply QFE 900713, then add /EXTINTVEC to the boot options using NVRBOOT. • Disconnect all drives except the boot drive prior to OS installation Only the target operating system drive should be connected during installation. This ensures that the operating system is installed on the correct drive. Make sure that the Z: drive letter is free. Windows Server 2003 with SP1 creates the EFI partition here. HP recommends that you install the boot controller in the root cell. 38 Installing Windows Server 2003

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
2.
If you choose to install from a GUI console you are prompted to specify server settings when
the Windows setup is complete.
Post-Installation Tasks
Perform the following tasks in the order shown. The operating system must be installed before
performing these tasks :
1.
Apply the operating system and security updates from the HP Smart Update DVD.
2.
Install the HP Support Pack from the HP Smart Setup CD to update firmware and device
drivers.
3.
Install updates from the HP website.
4.
Enable Windows Components.
a.
Install TCP/IP.
b.
Install SNMP.
c.
Configure SNMP.
5.
Install Management Tools.
a.
Install Partition Management tools.
b.
Install System Management Homepage.
c.
Install Management Agents.
Tips and Tricks
The following tips enable you to overcome some issues you might encounter while deploying
your Integrity server.
•
Install Service Pack 2
This upgrade is necessary for Intel Dual Core Itanium processor support.
•
Enable hyper-threading on Integrity servers
The default setting for hyper-threading is off. To enable hyper-threading, go to the EFI shell
and enter
cpuconfig threads on
. To disable hyper-threading, go to the EFI shell and
enter
cpuconfig threads off
.
•
Enable remote desktop connection from a headless server
The remote administration mode is enabled by default on Windows Server 2003 if you are
using the operating system supplied as part of the HP reinstall media. If you are installing
or reinstalling using Microsoft RTM media, the Remote Desktop functionality is disabled.
To enable remote desktop connections, the following WMIC command:
WMIC RdToggle WHERE AllowTSConnections=0 CALL SetAllowTSConnections
1
To enable remote desktop traffic through the Windows Firewall, enter:
netsh firewall set service remotedesktop enable all
•
Enable greater than 256 interrupts (cell-based servers only)
When using Windows Server 2003 on cell-based servers, the system only allows 256
interrupts. To overcome this limitation, apply QFE 900713, then add
/EXTINTVEC
to the
boot options using NVRBOOT.
•
Disconnect all drives except the boot drive prior to OS installation
Only the target operating system drive should be connected during installation. This ensures
that the operating system is installed on the correct drive. Make sure that the Z: drive letter
is free. Windows Server 2003 with SP1 creates the EFI partition here. HP recommends that
you install the boot controller in the root cell.
38
Installing Windows Server 2003