HP LH4r HP Netserver LH 3/3r User Guide - Page 59

Type 1--Mounting the Slides

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

Chapter 8 Mounting the NetServer in a Rack Type 1--Mounting the Slides Once you have marked the locations of the slides, attach them. To do so for the "Type 1" Rack, follow these steps : ◊ First, orient the slides so the slide members extend out the front of the rack. ◊ Insert screws through the rack column and start them in one bar nut at the correct location on each column (see Figure 8-5). Prepare to insert the mounting flange of the slides between the column and the bar nut. (Refer to Figure 8-6.) ◊ Then line up the front and rear mounting flanges of the slide with the screws started in the bar nuts. Press the slide firmly against the rack column. See Figure 8-8. ◊ Tighten all four screws in the mounting flanges of each slide. For Type 1 rack, insert screws through all four rack columns and start them in bar nuts. Mounting Flange Then insert the mounting flange in place on each column and tighten the screws. Figure 8-8. Orientation and Fastening of Type 1 Slides 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
Chapter 8
Mounting the NetServer in a Rack
51
Type 1--Mounting the Slides
Once you have marked the locations of the slides, attach them. To do so for the
"Type 1" Rack, follow these steps :
◊
First, orient the slides so the slide members extend out the front
of the rack.
◊
Insert screws through the rack column and start them in one bar nut at
the correct location on each column (see Figure 8-5). Prepare to insert
the mounting flange of the slides between the column and the bar nut.
(Refer to Figure 8-6.)
◊
Then line up the front and rear mounting flanges of the slide with the
screws started in the bar nuts. Press the slide firmly against the rack
column. See Figure 8-8.
◊
Tighten all four screws in the mounting flanges of each slide.
Mounting
Flange
Then insert the
mounting flange
in place on
each column and
tighten the screws.
For Type 1 rack, insert
screws through all four rack
columns and start them in bar nuts.
Figure 8-8.
Orientation and Fastening of Type 1 Slides