HP LH4r HP Netserver LH 3/3r User Guide - Page 78

Custom Configuration

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 78 highlights

Chapter 10 Configuring the NetServer • Install NOS: ◊ Automated NOS Installation: For certain versions of Novell NetWare / IntranetWare or Microsoft Windows NT Server, Configuration Assistant partitions and formats the hard disk drive, and Installation Assistant guides you through the NOS installation and configures the NOS with the appropriate drivers for the HP-bundled configuration. ◊ Manual NOS Installation: Follow the instructions on the screen and the Network Operating System Installation Instructions that you printed out. Custom Configuration In Custom configuration mode, you perform the same configuration steps as for Express configuration mode, but you can do them in any order. Select Custom on the Configuration Assistant menu if you are experienced in NetServer configuration and have a preferred sequence of steps, or if you prefer to configure your system one component at a time. After you have selected the NOS, version, and NOS installation mode (automated or manual), and after you have viewed the Configuration Advisories, the Custom Configuration screen displays the following menu: • Essential Steps: ◊ Configure Remote Management: This utility configures the Integrated Remote Management device for remote management. It enables remote, dial-up server management. To configure Integrated Remote Assistant, select Configure Remote Management on the Configure Remote Management screen. ◊ Configure Mass Storage: The HP NetServer is shipped with the hot-swap drive unconfigured. Do ONE of the following: 1. Run HP NetRAID Assistant to configure one or more RAID logical drives. Select "Execute" on the Configure Disk Array screen to start the HP NetRAID Assistant. For more information, refer to the Integrated HP NetRAID Controller Configuration Guide. 2. Exclude SCSI A channel from the integrated HP NetRAID controller, as follows: a. Restart the HP NetServer. b. When you see the message "Press to enter SETUP" on the monitor, press the F2 function key. 70

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
Chapter 10
Configuring the NetServer
70
•
Install NOS:
◊
Automated NOS Installation: For certain versions of Novell NetWare /
IntranetWare or Microsoft Windows NT Server, Configuration
Assistant partitions and formats the hard disk drive, and Installation
Assistant guides you through the NOS installation and configures the
NOS with the appropriate drivers for the HP-bundled configuration.
◊
Manual NOS Installation: Follow the instructions on the screen and
the Network Operating System Installation Instructions that you
printed out.
Custom Configuration
In Custom configuration mode, you perform the same configuration steps as for
Express configuration mode, but you can do them in any order. Select Custom on
the Configuration Assistant menu if you are experienced in NetServer
configuration and have a preferred sequence of steps, or if you prefer to configure
your system one component at a time.
After you have selected the NOS, version, and NOS installation mode (automated
or manual), and after you have viewed the Configuration Advisories, the Custom
Configuration screen displays the following menu:
•
Essential Steps:
◊
Configure Remote Management: This utility configures the Integrated
Remote Management device for remote management. It enables
remote, dial-up server management. To configure Integrated Remote
Assistant, select Configure Remote Management on the Configure
Remote Management screen.
◊
Configure Mass Storage: The HP NetServer is shipped with the
hot-swap drive unconfigured. Do ONE of the following:
1.
Run HP NetRAID Assistant to configure one or more RAID logical
drives. Select "Execute" on the Configure Disk Array screen to
start the HP NetRAID Assistant. For more information, refer to the
Integrated HP NetRAID Controller Configuration Guide
.
2.
Exclude SCSI A channel from the integrated HP NetRAID
controller, as follows:
a.
Restart the HP NetServer.
b.
When you see the message "Press <F2> to enter SETUP" on
the monitor, press the F2 function key.