HP LH4r HP Netserver LH 3/3r User Guide - Page 79

Select View Resources on the Show System Information screen to display

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 79 highlights

Chapter 10 Configuring the NetServer c. When the Setup Utility menu appears, use the up and down arrow keys to highlight "Included SCSI A Channel [Yes]." d. Use the +/- keys to change it to "Included SCSI A Channel [No]." e. Press the F10 function key to save and exit. f. Answer "Yes" to the question, "Save configuration and exit now?" The NetServer will start up again, and HP Navigator will restart. ◊ Execute Board Utilities: When HP Navigator finds installed boards for which there are additional configuration utilities on the CD-ROM, this option becomes available to complete the configuration of the boards. Select Execute on the Execute Board Utilities screen. ◊ Install NOS (in automated NOS installation mode), or Create Drivers Diskette(s) (in manual NOS installation mode) • Recommended Steps: ◊ Update System BIOS: Use this to update the system BIOS to the newer version on the HP NetServer Navigator CD-ROM. ◊ Install Utility Partition: This step creates an 8 MB utility partition on the server hard disk where HP Navigator will copy Diagnostic Assistant, the BIOS update utility, the event log report utility, the disk array utility, the NIC configuration utility, the Integrated Remote Assistant utilities, troubleshooting utilities, and other utilities. It is not available for SCO UNIX. Select Execute on the Install Utility Partition screen. • Select View System Information on the Show System Information screen to display information about standard and accessory boards and devices in the system. • Select View Resources on the Show System Information screen to display used and available system resources, such as memory ranges, I/O port ranges, DMA channels, and interrupt (IRQ) levels. ◊ Show NOS Installation Instructions: Select this option and Save to Disk to copy the Network Operating System Installation Instructions to disk. Then print them out from the disk. Read the instructions first, and then follow them to manually install the NOS. 71

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
Chapter 10
Configuring the NetServer
71
c.
When the Setup Utility menu appears, use the up and down
arrow keys to highlight "Included SCSI A Channel [Yes]."
d.
Use the +/- keys to change it to "Included SCSI A Channel
[No]."
e.
Press the F10 function key to save and exit.
f.
Answer "Yes" to the question, "Save configuration and exit
now?" The NetServer will start up again, and HP Navigator
will restart.
◊
Execute Board Utilities: When HP Navigator finds installed boards for
which there are additional configuration utilities on the CD-ROM, this
option becomes available to complete the configuration of the boards.
Select Execute on the Execute Board Utilities screen.
◊
Install NOS (in automated NOS installation mode), or Create Drivers
Diskette(s) (in manual NOS installation mode)
•
Recommended Steps:
◊
Update System BIOS: Use this to update the system BIOS to the newer
version on the
HP NetServer Navigator CD-ROM
.
◊
Install Utility Partition: This step creates an 8 MB utility partition on
the server hard disk where HP Navigator will copy Diagnostic
Assistant, the BIOS update utility, the event log report utility, the disk
array utility, the NIC configuration utility, the Integrated Remote
Assistant utilities, troubleshooting utilities, and other utilities. It is not
available for SCO UNIX. Select Execute on the Install Utility Partition
screen.
•
Select View System Information on the Show System Information screen
to display information about standard and accessory boards and devices in
the system.
•
Select View Resources on the Show System Information screen to display
used and available system resources, such as memory ranges, I/O port
ranges, DMA channels, and interrupt (IRQ) levels.
◊
Show NOS Installation Instructions: Select this option and Save to
Disk to copy the Network Operating System Installation Instructions
to disk. Then print them out from the disk. Read the instructions first,
and then follow them to manually install the NOS.