HP LH4r HP Netserver LH 3/3r User Guide - Page 61

washer and hex nut that held the mounting flanges in place. See

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

Chapter 8 Mounting the NetServer in a Rack ◊ Before attaching the slides, take off the removable mounting flanges from the rear of each slide and save two hex nuts and lock washers. ◊ Next, orient the slides so the slide members extend out the front of the rack. ◊ Start screws in one bar nut at the correct location on the front columns. Leave the screws loose enough to accept the slide mounting flange. Refer to Figures 8-5 and 8-6. ◊ Insert the threaded stud on the rear of the slide through the inside face on the rear column of the rack. Fasten it in place using the lock washer and hex nut that held the mounting flanges in place. See Figure 8-10. ◊ Press the slide tightly against the rack columns. ◊ Tighten the screws inserted in the bar nuts to hold the front flanges of the slides in place. 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
Chapter 8
Mounting the NetServer in a Rack
53
◊
Before attaching the slides, take off the removable mounting flanges
from the rear of each slide and save two hex nuts and lock washers.
◊
Next, orient the slides so the slide members extend out the front of the
rack.
◊
Start screws in one bar nut at the correct location on the front
columns.
Leave the screws loose enough to accept the slide mounting
flange. Refer to Figures 8-5 and 8-6.
◊
Insert the threaded stud on the rear of the slide through the inside face
on the rear column of the rack. Fasten it in place using the lock
washer and hex nut that held the mounting flanges in place. See
Figure 8-10.
◊
Press the slide tightly against the rack columns.
◊
Tighten the screws inserted in the bar nuts to hold the front flanges of
the slides in place.