HP LH4r HP Netserver LH 3000/3000r to LH 6000/6000r Upgrade Guide - Page 40

Run the Basic System Test

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Chapter 5 Updating Firmware 7. Click Exit and press Enter to exit HP NetServer Navigator and restart the NetServer. If the NetServer does not restart, turn off the NetServer power, wait 10 seconds, and turn on power again. NOTE HP DiagTools Diskette #1 contains a readme file of release notes. View the readme file to look for the most recent information about DiagTools. Run the Basic System Test Running the Basic System Test has two parts: l In Configuration Detection, DiagTools identifies all installed components. l The Basic System Test gives pass/fail results on each detected component. To run the Basic System Test: 1. Insert HP DiagTools Diskette #1 and restart the NetServer if you haven't done so already. The Welcome screen appears. 2. Press F2 and follow the instructions on the screen to begin Configuration Detection. HP DiagTools scans the NetServer and identifies all installed components, such as processors, memory, and SCSI devices. 3. Scroll through the list of detected components, and make note of any items that were not detected. HP DiagTools cannot test components it has not detected. NOTE HP DiagTools does not list the CD-ROM drive on the Configuration Detection screen, but it shows up in the Support Ticket and can be tested using the Advanced System tests. HP DiagTools is not designed to handle hot swapping. If you hot swap any components while HP DiagTools is running, you must restart DiagTools and perform a new Configuration Detection. 36

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
Chapter 5
Updating Firmware
36
7. Click
Exit
and press
Enter
to exit HP NetServer Navigator and restart the
NetServer.
If the NetServer does not restart, turn off the NetServer power, wait 10
seconds, and turn on power again.
NOTE
HP DiagTools Diskette #1
contains a
readme
file of release
notes. View the
readme
file to look for the most recent
information about DiagTools.
Run the Basic System Test
Running the Basic System Test has two parts:
In Configuration Detection, DiagTools identifies all installed components.
The Basic System Test gives pass/fail results on each detected component.
To run the Basic System Test:
1. Insert
HP DiagTools Diskette #1
and restart the NetServer if you haven’t
done so already.
The Welcome screen appears.
2. Press
F2
and follow the instructions on the screen to begin Configuration
Detection.
HP DiagTools scans the NetServer and identifies all installed components,
such as processors, memory, and SCSI devices.
3.
Scroll through the list of detected components, and make note of any items
that were not detected. HP DiagTools cannot test components it has not
detected.
NOTE
HP DiagTools does not list the CD-ROM drive on the
Configuration Detection screen, but it shows up in the Support
Ticket and can be tested using the Advanced System tests.
HP DiagTools is not designed to handle hot swapping. If you
hot swap any components while HP DiagTools is running, you
must restart DiagTools and perform a new Configuration
Detection.