HP LH4r HP Netserver LXr Pro8 User Guide - Page 18

Power-Up and Power-Down Procedures

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Chapter 2 Controls, Indicators, and Ports Power-Up and Power-Down Procedures Power-Up Procedure 1. Make sure that the power interlock switch at the rear of the HP NetServer is in the locked position, and that AC power is connected. When the switch is locked, the slot through the middle of the switch is vertical. See Figure 2-4. ◊ If the power interlock switch was unlocked, the system starts as soon as you relock the switch if AC power is connected. Skip ahead to step 3. ◊ If the power interlock switch was already locked, proceed to step 2. NOTE The interlock switch locks the satellite chassis in place. As a safety precaution, the server cannot power up unless this switch is locked. The HP NetServer cannot start unless the Power Interlock Switch is in this position Figure 2-4. Power Interlock Switch in Locked Position 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
Chapter 2
Controls, Indicators, and Ports
10
Power-Up and Power-Down Procedures
Power-Up Procedure
1.
Make sure that the power interlock switch at the rear of the HP NetServer
is in the locked position, and that AC power is connected. When the
switch is locked, the slot through the middle of the switch is vertical. See
Figure 2-4.
◊
If the power interlock switch was unlocked, the system starts as soon
as you relock the switch if AC power is connected. Skip ahead to
step 3.
◊
If the power interlock switch was already locked, proceed to step 2.
NOTE
The interlock switch locks the satellite chassis in place. As a
safety precaution, the server cannot power up unless this
switch is locked.
The HP NetServer
cannot start unless
the Power Interlock
Switch is in this position
Figure 2-4. Power Interlock Switch in Locked Position