HP LH4r HP Netserver LXr Pro8 User Guide - Page 55

Screw the board's I/O bracket to the I/O panel.

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

Chapter 6 Installing Additional Boards d. Embedded SCSI controllers 1 through 7. (These controllers are only accessible in servers equipped with the optional SCSI Extender Board accessory.) e. PCI slots 1 through 8. 4. When you have selected a slot, remove its slot cover on the I/O panel. 5. Push the board down into its connector on the system board (Figure 6-2). Figure 6-2. Inserting the Board 6. Screw the board's I/O bracket to the I/O panel. 7. If the board you added must be cabled to the system board or chassis, make sure that the cable is properly attached. Refer to the board documentation. 8. Close the top cover. (See Chapter 3.) 47

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
Chapter 6
Installing Additional Boards
47
d.
Embedded SCSI controllers 1 through 7. (These controllers are only
accessible in servers equipped with the optional SCSI Extender Board
accessory.)
e.
PCI slots 1 through 8.
4.
When you have selected a slot, remove its slot cover on the I/O panel.
5.
Push the board down into its connector on the system board (Figure 6-2).
Figure 6-2. Inserting the Board
6.
Screw the board's I/O bracket to the I/O panel.
7.
If the board you added must be cabled to the system board or chassis,
make sure that the cable is properly attached. Refer to the board
documentation.
8.
Close the top cover. (See Chapter 3.)