HP Scanjet 5000 User Guide - Page 53

Population order, Installing a DIMM, After installing the DIMMs

Get HP Scanjet 5000 PDF manuals and user guides View all HP Scanjet 5000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

● Each channel can have a different valid online spare configuration. ● Each populated channel must have a spare rank: A single dual-rank DIMM is not a valid configuration. Population order For memory configurations with a single processor or multiple processors, DIMMs must be populated sequentially in alphabetical order (A through L). After installing the DIMMs, use the BIOS/Platform Configuration (RBSU) in the UEFI System Utilities to configure supported AMP modes. Installing a DIMM The server supports up to 24 DIMMs. To install a DIMM: 1. Power down the server (see Powering down the server on page 16). 2. Remove all power: a. Disconnect each power cord from the power source. b. Disconnect each power cord from the server. 3. Do one of the following: a. Extend the server from the rack (see Extending the server from the rack on page 17). b. Remove the server from the rack (see Removing the server from the rack on page 17). 4. Remove the access panel (see Removing the access panel on page 18). 5. Remove the air baffle (see Removing the air baffle on page 25). 6. Open the DIMM slot latches. 7. Install the DIMM. 8. Install the air baffle. 9. Install the access panel (see Installing the access panel on page 18). 10. Install the server into the rack (see Installing the server into the rack on page 30). Memory options 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
●
Each channel can have a different valid online spare configuration.
●
Each populated channel must have a spare rank: A single dual-rank DIMM is not a valid configuration.
Population order
For memory configurations with a single processor or multiple processors, DIMMs must be populated
sequentially in alphabetical order (A through L).
After installing the DIMMs, use the BIOS/Platform Configuration (RBSU) in the UEFI System Utilities to
configure supported AMP modes.
Installing a DIMM
The server supports up to 24 DIMMs. To install a DIMM:
1.
Power down the server (see
Powering down the server
on page
16
).
2.
Remove all power:
a.
Disconnect each power cord from the power source.
b.
Disconnect each power cord from the server.
3.
Do one of the following:
a.
Extend the server from the rack (see
Extending the server from the rack
on page
17
).
b.
Remove the server from the rack (see
Removing the server from the rack
on page
17
).
4.
Remove the access panel (see
Removing the access panel
on page
18
).
5.
Remove the air baffle (see
Removing the air baffle
on page
25
).
6.
Open the DIMM slot latches.
7.
Install the DIMM.
8.
Install the air baffle.
9.
Install the access panel (see
Installing the access panel
on page
18
).
10.
Install the server into the rack (see
Installing the server into the rack
on page
30
).
Memory options
45