HP Scanjet 5000 User Guide - Page 54

Hot-plug hard drive options

Get HP Scanjet 5000 PDF manuals and user guides View all HP Scanjet 5000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

11. Connect each power cord to the server. 12. Connect each power cord to the power source. 13. Power up the server (see Powering up the server on page 16). Use the BIOS/Platform Configuration (RBSU) in the UEFI System Utilities to configure the memory mode. For more information about LEDs and troubleshooting failed DIMMs, see Systems Insight Display LED combinations on page 5. Hot-plug hard drive options When adding hard drives to the server, observe the following general guidelines: ● The system automatically sets all device numbers. ● If only one drive is used, install it in the bay with the lowest device number. ● Drives should be the same capacity to provide the greatest storage space efficiency when drives are grouped together into the same drive array. 46 Chapter 5 Hardware options installation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
11.
Connect each power cord to the server.
12.
Connect each power cord to the power source.
13.
Power up the server (see
Powering up the server
on page
16
).
Use the BIOS/Platform Configuration (RBSU) in the UEFI System Utilities to configure the memory mode.
For more information about LEDs and troubleshooting failed DIMMs, see
Systems Insight Display LED
combinations
on page
5
.
Hot-plug hard drive options
When adding hard drives to the server, observe the following general guidelines:
●
The system automatically sets all device numbers.
●
If only one drive is used, install it in the bay with the lowest device number.
●
Drives should be the same capacity to provide the greatest storage space efficiency when drives are
grouped together into the same drive array.
46
Chapter 5
Hardware options installation