HP Scanjet 5000 User Guide - Page 66

-slot PCI riser cage option, Do one of the following

Get HP Scanjet 5000 PDF manuals and user guides View all HP Scanjet 5000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 66 highlights

12. Connect each power cord to the server. 13. Connect each power cord to the power source. 14. Power up the server (see Powering up the server on page 16). 3-slot PCI riser cage option WARNING! To reduce the risk of personal injury, electric shock, or damage to the equipment, remove the power cord to remove power from the server. The front panel Power On/Standby button does not completely shut off system power. Portions of the power supply and some internal circuitry remain active until AC power is removed. CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless all PCI slots have either an expansion slot cover or an expansion board installed. To install the component: 1. Power down the server (see Powering down the server on page 16). 2. Remove all power: a. Disconnect each power cord from the power source. b. Disconnect each power cord from the server. 3. Do one of the following: ● Extend the server from the rack (see Extending the server from the rack on page 17). ● Remove the server from the rack (see Removing the server from the rack on page 17). 4. Remove the access panel (see Removing the access panel on page 18). 5. Remove the secondary PCI riser blank. Some models might require removing only two screws. 58 Chapter 5 Hardware options installation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
12.
Connect each power cord to the server.
13.
Connect each power cord to the power source.
14.
Power up the server (see
Powering up the server
on page
16
).
3-slot PCI riser cage option
WARNING!
To reduce the risk of personal injury, electric shock, or damage to the equipment, remove the
power cord to remove power from the server. The front panel Power On/Standby button does not completely
shut off system power. Portions of the power supply and some internal circuitry remain active until AC power
is removed.
CAUTION:
To prevent improper cooling and thermal damage, do not operate the server unless all PCI slots
have either an expansion slot cover or an expansion board installed.
To install the component:
1.
Power down the server (see
Powering down the server
on page
16
).
2.
Remove all power:
a.
Disconnect each power cord from the power source.
b.
Disconnect each power cord from the server.
3.
Do one of the following:
●
Extend the server from the rack (see
Extending the server from the rack
on page
17
).
●
Remove the server from the rack (see
Removing the server from the rack
on page
17
).
4.
Remove the access panel (see
Removing the access panel
on page
18
).
5.
Remove the secondary PCI riser blank. Some models might require removing only two screws.
58
Chapter 5
Hardware options installation