HP Server tc3100 hp server tc3100 operation and maintenance guide (English, v1 - Page 18

Opening the Upper Bezel, Opening the Lower Bezel Cold Swap Model, See

Get HP Server tc3100 PDF manuals and user guides View all HP Server tc3100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Chapter 3 Installing and Configuring Opening the Upper Bezel You need to open the upper bezel to remove and replace the flexible disk drive and CD-ROM, or add a tape device. · If you are installing or removing SCSI cold swap hard drives, you must open the upper bezel to open the lower bezel. · If you are installing hardware options, you need only unlock the front bezel; the bezel does not have to be open. The hardware options include accessory boards, DIMMs, and an additional processor, which are accessed through the side panel. 1. Power off the server and disconnect all power cords and any telecommunications cables. 2. Unlock the upper bezel. 3. Hold the bezel at the notch on the side panel and swing the bezel open to the right. See Figure 3-2. Figure 3-2. Upper Bezel (Open) Opening the Lower Bezel (Cold Swap Model) The only reason to open the lower bezel is to access the SCSI cold swap hard drives. 1. Power off the server and disconnect all power cords and any telecommunications cables. 2. Open the upper bezel. 3. Press down on the two tabs at the top of the lower bezel, pull the bezel toward you, and lower the door. See Figure 3-3. 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
Chapter 3
Installing and Configuring
12
Opening the Upper Bezel
You need to open the upper bezel to remove and replace the flexible disk drive and CD-ROM, or add a tape
device.
±²
If you are installing or removing SCSI cold swap hard drives, you must open the upper bezel to open the
lower bezel.
±²
If you are installing hardware options, you need only unlock the front bezel; the bezel does not have to
be open. The hardware options include accessory boards, DIMMs, and an additional processor, which
are accessed through the side panel.
1.
Power off the server and disconnect all power cords and any telecommunications cables.
2. Unlock the upper bezel.
3.
Hold the bezel at the notch on the side panel and swing the bezel open to the right. See Figure 3-2.
Figure 3-2. Upper Bezel (Open)
Opening the Lower Bezel (Cold Swap Model)
The only reason to open the lower bezel is to access the SCSI cold swap hard drives.
1.
Power off the server and disconnect all power cords and any telecommunications cables.
2. Open the upper bezel.
3.
Press down on the two tabs at the top of the lower bezel, pull the bezel toward you, and lower the door.
See Figure 3-3.