HP mt245 mt245 Mobile Thin Client Maintenance and Service Guide - Page 36

Solid-state drive, 2.5-inch, To remove the solid-state drive

Get HP mt245 PDF manuals and user guides View all HP mt245 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

Reverse this procedure to install the bottom cover. Solid-state drive, 2.5-inch Before removing the solid-state drive, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer. 4. Remove the battery (see Battery on page 24). 5. Remove the bottom cover (see Bottom cover on page 25). To remove the solid-state drive: 1. Disconnect the drive cable from the system board (1). 2. Lift the drive assembly from the computer (2). 3. To disassemble the solid-state drive, pull the connector away from the drive to remove it (1). 28 Chapter 5 Removal and replacement procedures for Authorized Service Provider parts

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
Reverse this procedure to install the bottom cover.
Solid-state drive, 2.5-inch
Before removing the solid-state drive, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is
off
or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by
first
unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the computer.
4.
Remove the battery (see
Battery
on page
24
).
5.
Remove the bottom cover (see
Bottom cover
on page
25
).
To remove the solid-state drive:
1.
Disconnect the drive cable from the system board
(1)
.
2.
Lift the drive assembly from the computer
(2)
.
3.
To disassemble the solid-state drive, pull the connector away from the drive to remove it
(1)
.
28
Chapter 5
Removal and replacement procedures for Authorized Service Provider parts