IBM 72332MU Installation Guide - Page 35

If necessary, remove the microprocessor air baffle from between socket 1

Get IBM 72332MU - System x3950 M2 PDF manuals and user guides
UPC - 883436084673
View all IBM 72332MU manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

2. Microprocessor socket 2 must always contain either a heat-sink blank or a microprocessor and heat sink. 3. The microprocessor air-baffle must always be installed between microprocessor socket 1 and socket 2. To install an additional microprocessor, complete the following steps: 1. Read the safety information that begins on page v and "Installation guidelines" on page 9. 2. Turn off the server and peripheral devices, and disconnect the power cords and all external cables as necessary to replace the device. 3. Remove the server cover and bezel. Attention: When you handle static-sensitive devices, take precautions to avoid damage from static electricity. For details about handling these devices, see "Handling static-sensitive devices" on page 11. 4. Loosen the captive screws and rotate the media hood to the fully open position. Captive screws 5. If necessary, remove the microprocessor air baffle from between socket 1 and socket 2. 6. If you are installing a microprocessor in microprocessor socket 2, remove the heat-sink blank and store it for future use. 7. Remove the protective cover, tape, or label from the surface of the microprocessor socket, if any is present. Lever closed Lever fully open 8. Lift the microprocessor-release lever to the fully-open position (approximately 135° angle). Chapter 2. Installing optional devices 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
2.
Microprocessor socket 2 must always contain either a heat-sink blank or a
microprocessor and heat sink.
3.
The microprocessor air-baffle must always be installed between
microprocessor socket 1 and socket 2.
To install an additional microprocessor, complete the following steps:
1.
Read the safety information that begins on page v and “Installation guidelines”
on page 9.
2.
Turn off the server and peripheral devices, and disconnect the power cords
and all external cables as necessary to replace the device.
3.
Remove the server cover and bezel.
Attention:
When you handle static-sensitive devices, take precautions to
avoid damage from static electricity. For details about handling these devices,
see “Handling static-sensitive devices” on page 11.
4.
Loosen the captive screws and rotate the media hood to the fully open
position.
Captive
screws
5.
If necessary, remove the microprocessor air baffle from between socket 1 and
socket 2.
6.
If you are installing a microprocessor in microprocessor socket 2, remove the
heat-sink blank and store it for future use.
7.
Remove the protective cover, tape, or label from the surface of the
microprocessor socket, if any is present.
Lever closed
Lever fully
open
8.
Lift the microprocessor-release lever to the fully-open position (approximately
135° angle).
Chapter 2. Installing optional devices
23