IBM 8478 Hardware Maintenance Manual - Page 70

information

Get IBM 8478 - Eserver xSeries 200 PDF manuals and user guides
UPC - 087944650553
View all IBM 8478 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 70 highlights

Attention: When you handle ESD-sensitive devices, take precautions to avoid damage from static electricity, see "Handling static-sensitive devices" on page 45. 1. Read the information in "Preinstallation steps (all bays)" on page 56. 2. Turn off the server and peripheral devices and disconnect all external cables and power cords; then, remove the cover (see "Removing the side cover" on page 46 for details). 3. Remove the support bracket assembly. See "Removing the support bracket assembly" on page 49. 4. Remove the support bracket assembly and disconnect the fan cable from the connector (SYSFA3) on the system board. See "Removing the support bracket assembly" on page 49 and "System board internal cable connectors" on page 42 for the location of the fan cable connector. 5. Access the drive cage. a. If your server has hard disk drives installed in the drive cage, disconnect the power and signal cables from the rear of the drives. b. Rotate the drive cage out of the server until it locks into place over the drive cage retention tab. Note: Before you install a hard disk drive, ensure that the drive cage locks into place over the drive cage retention tab by pressing on the side of the drive cage. 6. Attach the blue, plastic guide rails to the sides of the drive using the screws provided. 7. Slide the drive into the drive cage until the plastic tabs on the guide rails lock into place in the drive cage. 8. Lift the drive cage up and press in on the drive cage release tab; then, rotate the drive cage back into the server. Note: Clear any cables that might impede the replacement of the drive cage. 9. Connect the power and signal cables to the rear of each drive. Note: Make sure to route the signal cable so that it does not block the air flow to the rear of the drives or over the microprocessor. 10. If you have other options to install or remove, do so now. 11. Replace the support bracket assembly and reconnect the fan cable to the connector (SYSFA3) on the 60 Hardware Maintenance Manual: xSeries 200

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
Attention:
When
you
handle
ESD-sensitive
devices,
take
precautions
to
avoid
damage
from
static
electricity,
see
“Handling
static-sensitive
devices”
on
page
45.
1.
Read
the
information
in
“Preinstallation
steps
(all
bays)”
on
page
56.
2.
Turn
off
the
server
and
peripheral
devices
and
disconnect
all
external
cables
and
power
cords;
then,
remove
the
cover
(see
“Removing
the
side
cover”
on
page
46
for
details).
3.
Remove
the
support
bracket
assembly.
See
“Removing
the
support
bracket
assembly”
on
page
49.
4.
Remove
the
support
bracket
assembly
and
disconnect
the
fan
cable
from
the
connector
(SYSFA3)
on
the
system
board.
See
“Removing
the
support
bracket
assembly”
on
page
49
and
“System
board
internal
cable
connectors”
on
page
42
for
the
location
of
the
fan
cable
connector.
5.
Access
the
drive
cage.
a.
If
your
server
has
hard
disk
drives
installed
in
the
drive
cage,
disconnect
the
power
and
signal
cables
from
the
rear
of
the
drives.
b.
Rotate
the
drive
cage
out
of
the
server
until
it
locks
into
place
over
the
drive
cage
retention
tab.
Note:
Before
you
install
a
hard
disk
drive,
ensure
that
the
drive
cage
locks
into
place
over
the
drive
cage
retention
tab
by
pressing
on
the
side
of
the
drive
cage.
6.
Attach
the
blue,
plastic
guide
rails
to
the
sides
of
the
drive
using
the
screws
provided.
7.
Slide
the
drive
into
the
drive
cage
until
the
plastic
tabs
on
the
guide
rails
lock
into
place
in
the
drive
cage.
8.
Lift
the
drive
cage
up
and
press
in
on
the
drive
cage
release
tab;
then,
rotate
the
drive
cage
back
into
the
server.
Note:
Clear
any
cables
that
might
impede
the
replacement
of
the
drive
cage.
9.
Connect
the
power
and
signal
cables
to
the
rear
of
each
drive.
Note:
Make
sure
to
route
the
signal
cable
so
that
it
does
not
block
the
air
flow
to
the
rear
of
the
drives
or
over
the
microprocessor.
10.
If
you
have
other
options
to
install
or
remove,
do
so
now.
11.
Replace
the
support
bracket
assembly
and
reconnect
the
fan
cable
to
the
connector
(SYSFA3)
on
the
60
Hardware
Maintenance
Manual:
xSeries
200