Icom IC-7610 Instruction Manual basic

Icom IC-7610 Manual

Get Icom IC-7610 PDF manuals and user guides View all Icom IC-7610 manuals
Add to My Manuals
Save this manual to your list of manuals

Icom IC-7610 manual content summary:

  • Icom IC-7610 | Instruction Manual basic - Page 1
    BASIC MANUAL HF/50 MHz TRANSCEIVER i7610
  • Icom IC-7610 | Instruction Manual basic - Page 2
    the design of your IC-7610. IMPORTANT READ ALL INSTRUCTIONS carefully completely before using the transceiver. SAVE THIS INSTRUCTION MANUAL- This instruction manual contains basic operating instructions for the IC7610. For the advanced operating instructions, see the Advanced Manual on the supplied
  • Icom IC-7610 | Instruction Manual basic - Page 3
    uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW. CAUTION: Changes or modifications to this device, not expressly approved by Icom Inc
  • Icom IC-7610 | Instruction Manual basic - Page 4
    the touch screen, be careful not to push it too hard or scratch it with your finger nails. Otherwise you may damage the screen. ABOUT THE SUPPLIED CD The following items are included on the CD. ••Basic manual (English) Instructions for basic operations, the same as this manual. ••Advanced manual
  • Icom IC-7610 | Instruction Manual basic - Page 5
    RTTY (FSK) and PSK ••Data mode (AFSK) operation ••Scope operation ••Voice Recorder functions ••Voice TX Memory operation ••Using an SD card and USB flash drive ••Memory operation ••Scan ••Set mode ••Clock and Timers ••Updating the firmware ••Replacing
  • Icom IC-7610 | Instruction Manual basic - Page 6
    INSTRUCTIONS The Basic and Advanced manuals are described in the following manner. " " (Quotation marks): Used to indicate icons, setting items, and screen titles displayed on the screen. The screen titles are also indicated in uppercase letters. (Example: FUNCTION screen) [ ] (brackets):  Used
  • Icom IC-7610 | Instruction Manual basic - Page 7
    iii ABOUT THE SUPPLIED CD iii ABOUT THE CONSTRUCTION OF THE MANUAL...iv ABOUT THE INSTRUCTIONS v PRECAUTIONS viii 1. PANEL DESCRIPTION 1-1 Front panel 1-1 Rear panel 1-3 Touch screen display 1-4 DDMENU screen 1-6 DDMulti-function menus 1-6 DDMulti-function key group 1-7 DDQUICK MENU
  • Icom IC-7610 | Instruction Manual basic - Page 8
    Formatting the SD card or USB flash drive 6-2 Unmounting 6-2 7. ANTENNA TUNER OPERATION 7-1 About the Antenna memory settings 7-1 DDThe Antenna memory screen 7-1 DDSaving an antenna connector setting.......... 7-1 DDSelecting the antenna type 7-2 About the internal antenna tuner 7-2 Using the
  • Icom IC-7610 | Instruction Manual basic - Page 9
    accessories at high volume levels. If you experience a ringing in your ears, reduce the volume or discontinue use. R WARNING! NEVER apply AC power to the [DC13.8V] socket on the transceiver rear panel. This could cause a fire or damage the transceiver. R WARNING! NEVER apply more than 16 V DC to the
  • Icom IC-7610 | Instruction Manual basic - Page 10
    Turns the Noise Reduction function ON or OFF. !1 NOISE BLANKER KEY NB (p. 4-5) Turns the Noise Blanker ON or OFF. !2 ANTENNA TUNER KEY TUNER (p. 7-3) Turns the antenna tuner ON or OFF, or activates the tuner. !3 !4 !5 !6 !7 !8 !9 @0 @1 !3 MENU KEY MENU (p. 8-1) Displays the MENU screen. !4 MINI
  • Icom IC-7610 | Instruction Manual basic - Page 11
    panel (Continued) !9 EXIT KEY EXIT Exits a setting screen or returns to the previous screen. @0 VOICE MEMORY RECORD KEY REC Saves the previously received signal for the preset time period set in REC Time, using the Instant Replay function, or starts recording a QSO audio onto an SD card the RTTY
  • Icom IC-7610 | Instruction Manual basic - Page 12
    PANEL DESCRIPTION Rear panel use the AH-4 or AH-740, you must connect the antenna to [ANT1]. y ALC INPUT JACK [ALC] Connects to the ALC output jack of a non-Icom linear amplifier. u SEND CONTROL JACK [SEND] Connects to control transmit with non-Icom external units. i E XTERNAL SPEAKER RTTY memory
  • Icom IC-7610 | Instruction Manual basic - Page 13
    1 PANEL DESCRIPTION Touch screen display q w er t y u i o !0 !1 w e r t yu i 1 2 @0 !9 !3 !2 3 !5 !3 4 !4 !4 !5 5 !6 !6 6 7 !7 the Auto Notch function is ON, and "MN" is displayed when the Manual Notch function is ON. !6 FREQUENCY READOUT (p. 3-4) Displays the operating
  • Icom IC-7610 | Instruction Manual basic - Page 14
    1 PANEL DESCRIPTION Touch screen display (Continued) @5 @6 @7 @8 @9 #0 #1 #2 #3 #4 @1 @4 @3 @2 @6 @7 @8 @9 @5 @4 @3 @2 @1 #9 #8 #7 #6 #5 $1 $0 #9 #8 Split function is ON. #1 DUALWATCH ICON (p. 3-2) Displayed when using Dualwatch. #2 SHIFT FREQUENCY READOUT (p. 4-1) Displays the shift offset
  • Icom IC-7610 | Instruction Manual basic - Page 15
    1 PANEL DESCRIPTION Touch screen display (Continued) DDMENU screen DDMulti-function menus Touch to turn ON or OFF Multi-function menu zzOpen the Multi-function menu by pushing MULTI (Multi-function control). zzWhile the Multi-function menu is open, touch the desired item and rotate MULTI to
  • Icom IC-7610 | Instruction Manual basic - Page 16
    1 PANEL DESCRIPTION Touch screen display (Continued) DDMulti-function key group Touch to turn ON or OFF, or to set Multi-function key group zzTouch a key to turn the function ON or OFF. zzTouching "ATT," "VOX," "BK-IN" or "COMP" for 1 second opens the ATT menu, VOX menu, BK-IN menu or COMP menu.
  • Icom IC-7610 | Instruction Manual basic - Page 17
    1 PANEL DESCRIPTION Keyboard entering and editing You can enter and edit the items on the following screens. LUsable characters, symbols, and the amount of characters that can be entered differs, depending on the editing item. 1 ••MY CALL ••FILE NAME 2 ••NETWORK NAME ••NETWORK RADIO NAME 3
  • Icom IC-7610 | Instruction Manual basic - Page 18
    1 PANEL DESCRIPTION Keypad entering and editing (Continued) DDEntering and editing example Entering "DX spot 1" in the Memory channel 2 1. Display the MEMORY screen. MENU » MEMORY 2. Touch the memory channel 2 for 1 second. ••The MEMORY MENU screen is displayed. 7. Touch [s], [p], [o], and then
  • Icom IC-7610 | Instruction Manual basic - Page 19
    3 ••DO NOT touch the rear panel after transmitting continuously for long periods of time. The panel may 4 become hot. 5 Grounding 6 To prevent electrical shock, television interference (TVI), 7 broadcast interference (BCI) and other problems, ground 8 the transceiver using the ground
  • Icom IC-7610 | Instruction Manual basic - Page 20
    instruction manual for installation and connection details. LSee the Advanced Manual for connecting the optional AH-740 automatic antenna tuner. NOTE: ••Before connecting, be sure to turn OFF the transceiver. ••While the AH-4 is connected, the IC-7610ʼs internal antenna tuner is deactivated. HF
  • Icom IC-7610 | Instruction Manual basic - Page 21
    See the illustration below to connect a non-Icom linear amplifier. LWe recommend that you use a linear amplifier with a specified input power of 100 watts or more. If you use an amplifier with a specified drive level of less than 100 watts, adjust the IC-7610's output power to the specified level
  • Icom IC-7610 | Instruction Manual basic - Page 22
    Memory modes VFO mode You can set a frequency by rotating MAIN DIAL . LUsing the VFO mode may be easier for the first initial operation. Memory mode You can Push QUICK . ••The QUICK MENU screen is displayed. 2. Touch "VFO/MEMORY." 3. Touch [VFO] or [Memory] to select the mode. VFO indicator
  • Icom IC-7610 | Instruction Manual basic - Page 23
    frequencies. 10 The IC-7610 has 2 independent receiver circuits, the Main and Sub bands, so that you can use Dualwatch 11 with no This Quick Dualwatch function can be turned OFF in the Others set screen. 21 (p. 8-3) 2. Touch the frequency readout of the band you want to set the frequency.
  • Icom IC-7610 | Instruction Manual basic - Page 24
    SET > Connectors > DATA1 MOD ~ DATA3 MOD (Example: USB-D mode) 1. While the USB mode is selected, touch the mode icon. 2. Touch [DATA]. ••[USB-D1] zzRepeatedly touching a band key on the BAND STACKING REGISTER screen for 1 second. TIP: See the Advanced Manual for details on using the Data mode
  • Icom IC-7610 | Instruction Manual basic - Page 25
    is displayed when you set an amateur radio frequency, and ("TX" with a screen. 7 The Tuning Step function 8 is ON. 9 10 11 12 13 DDUsing the 1 Hz step Fine Tuning function You can use the minimum tuning step of 1 Hz for fine tuning in the SSB, CW and RTTY modes as the default. 14 Touch
  • Icom IC-7610 | Instruction Manual basic - Page 26
    in the SSB-D, CW, RTTY and PSK modes. 1. Push MENU . 2. Touch [1/4]. DDDirectly entering a frequency You can directly enter a frequency using the keypad. Entering the operating frequency 1. Touch the MHz digits. (Example: 14) 2. Touch [F-INP]. ••Opens the F-INP screen. 3. Push EXIT to close
  • Icom IC-7610 | Instruction Manual basic - Page 27
    want to set a Program Channel number (P1 or P2), enter "100" for P1, and "101" for P2. 14 6. Touch [MEMO] to save the entered channel. 15 16 17 18 ••Closes the F-INP screen. 19 20 Dial Lock function 21 The Dial Lock function prevents frequency changes caused by accidently rotating MAIN
  • Icom IC-7610 | Instruction Manual basic - Page 28
    and Id) to display during transmit. Touch the meter to display one of the meters noise just disappears and the TX/RX indicator goes OFF. ••S-meter squelch The S-meter squelch disables the audio output from the speaker compression level when the speech compressor is used. Vd:  Displays the drain
  • Icom IC-7610 | Instruction Manual basic - Page 29
    in use once or twice, before you start operating. 11 12 DDAdjusting the transmit output power 1. Set the operating mode to SSB, CW, RTTY, PSK or FM. (p. 3-3) 2. Touch the meter the S-meter while receiving. 7. Release [PTT] (or push TRANSMIT again). ••Returns to receive. 18 19 20 21 3-8
  • Icom IC-7610 | Instruction Manual basic - Page 30
    on the microphone. ••The TX/RX indicator lights red and is displayed. 5. Rotate MULTI to adjust the microphone gain. 6. Release [PTT]. ••Returns to receive LLInformatio •• In the SSB mode, touch the TX meter to select the ALC meter, and adjust until the meter reading swings between 30 to 50% of
  • Icom IC-7610 | Instruction Manual basic - Page 31
    noise ratio and sensitivity. A preamp is used when the received signals are weak. LEach band memorizes the previously used Preamplifier setting. Touch [P.AMP]. LEach touch 20 ••The RIT function is temporarily OFF. ••The Noise Reduction, Notch filter and Twin PBT 21 settings are temporarily
  • Icom IC-7610 | Instruction Manual basic - Page 32
    set the time constant. LYou can reset to the default settings by touching [DEF] for 1 second. 5. To close the AGC screen, push EXIT . ••Selectable AGC Time constant (unit: seconds) Mode LSB USB CW RTTY PSK AM FM Default 0.3 （FAST） 2.0 （MID） 6.0 （SLOW） 0.1 （FAST） 0.5 （MID） 1.2 （SLOW） 3.0 （FAST
  • Icom IC-7610 | Instruction Manual basic - Page 33
    4 RECEIVING AND TRANSMITTING Using the Twin PBT SSB, CW, RTTY, PSK and AM modes To reject interference, the Twin PBT (Passband Tuning) narrows the IF passband width by electronically shifting the IF frequency slightly above or below the IF center frequency. The IC-7610 uses DSP for the PBT function
  • Icom IC-7610 | Instruction Manual basic - Page 34
    ••Opens the FILTER screen. 3. Touch FIL 1 (wide), FIL 2 (mid) or FIL 3 (narrow). 4. Touch [BW]. ••Selects 500 Hz or narrower, in the SSB or CW mode. Mode SSB SSB-D CW PSK RTTY AM AM-D FM FM-D IF filter FIL 1 (3.0 kHz) FIL 2 (2.4 kHz) analog filters. This decreases noise components in the high and
  • Icom IC-7610 | Instruction Manual basic - Page 35
    . The indicator lights. NOTE: When using the Noise Blanker, received signals may be distorted if they are excessively strong, or the noise is other than a pulse type. In that case, turn OFF the Noise Blanker, or shallow the DEPTH on the NB menu. See the instruction below for details. DDAdjusting the
  • Icom IC-7610 | Instruction Manual basic - Page 36
    Selector function 1. Push MENU to open the MENU screen. 2. Touch [DIGI-SEL] to turn ON the Digital Selector function ON. LTouching [DIGI-SEL] to turn the function ON or OFF. Notch Filter The IC-7610 has Auto Notch and Manual Notch functions. Auto Notch can be used in the SSB, AM and FM modes, and
  • Icom IC-7610 | Instruction Manual basic - Page 37
    manually attenuate the frequency. LTouching [NOTCH WIDTH] changes the Manual Notch filter width between "WIDE," "MID," and "NAR." NOTE: While adjusting, noise Push MENU . 5 ••Opens the MENU screen. 3. Touch [MONI] to turn ON the Monitor function When using the VOICE DELAY set in the VOX
  • Icom IC-7610 | Instruction Manual basic - Page 38
    exceed the COMP zone, your transmitted voice may be distorted. COMP zone 6. Touch the meter again to display the COMP meter. Auto Tuning function (AM/CW) range in the CW mode, or a ±5 kHz range in the AM mode. You can use this function only in the CW and AM modes. 1. Select the AM mode or CW
  • Icom IC-7610 | Instruction Manual basic - Page 39
    is displayed. ••The Main band settings are set to the Sub band. DDUsing the receive and transmit 9 frequencies set to Main and Sub 10 1. Set operating mode. 11 (Example: 21.29000 MHz in the USB mode) 2. Touch the Sub band's frequency readout to select 12 the Sub band, and then set
  • Icom IC-7610 | Instruction Manual basic - Page 40
    the receive frequency by releasing XFC while rotating MAIN DIAL , use the Split Lock function. Using both this function and operating mode to USB or LSB. 2. Touch [COMP] for 1 second. ••Opens the COMP menu on the right side of the screen. 3. Touch [TBW]. LTouching [TBW] sets the filter width to
  • Icom IC-7610 | Instruction Manual basic - Page 41
    Use the Break-in function in the CW mode to 1 automatically switch between transmit and receive when keying. The IC-7610 is capable of Semi Break-in 2 and Full break-in modes. 3 TIP: The key type is set to "Paddle" by default. You can select the keyer type on the CW-KEY SET screen
  • Icom IC-7610 | Instruction Manual basic - Page 42
    three APF passband width, WIDE, MID or NAR. 1. Select the CW mode. 2. Push APF/TPF to turn ON the Audio Peak Filter. APF/TPF Touch [BK-IN]. 3. Use a straight key or paddle to operate. LIn the Full break-in mode, the transceiver automatically returns to receive without a preset break-in delay time
  • Icom IC-7610 | Instruction Manual basic - Page 43
    the CW mode. 3 MENU » KEYER 4 LYou can select [KEYER] on the MENU screen only in the CW mode. 2. Touch [EDIT/SET]. 5 ••Opens the EDIT/SET screen. 6 7 8 9 10 KEYER SEND screen 3. Touch to select the item to set. EDIT 001 SET 11 KEYER MEMORY edit menu You can edit the keyer memories
  • Icom IC-7610 | Instruction Manual basic - Page 44
    select the Mini scope to display it in a smaller size on the screen. ••Center mode screen Span (Display range) Span (Display range) Center/Fixed Single scope. EXPD/ SET Touch Selects the Expanded or Normal screen. Touch 1 sec. Displays the SCOPE SET screen. REF Opens the Reference level
  • Icom IC-7610 | Instruction Manual basic - Page 45
    function display, such as the RTTY DECODE screen or AUDIO SCOPE screen. Push M.SCOPE . LPushing it again closes the Mini scope screen. TIP: Holding down M.SCOPE displays the spectrum scope screen, and pushing it again returns to the Mini scope screen. Audio scope screen This audio scope enables you
  • Icom IC-7610 | Instruction Manual basic - Page 46
    5 SCOPE OPERATION Audio scope screen (Continue) DDAUDIO SCOPE SET screen This screen is used to set the FFT scope waveform type, color, Waterfall display and oscilloscope waveform color. 1. Display the AUDIO SCOPE screen. MENU » AUDIO 2. Touch [SET]. 3. Touch to select the item to set. (
  • Icom IC-7610 | Instruction Manual basic - Page 47
    simply called the SD card or the card. About the USB flash drive Use the USB flash drive that supports the interface 1.1 or 2.0. LThese do not guarantee the USB flash drive's performance. NOTE: ••Before using the SD card or USB flash drive, thoroughly read the their instructions. ••If any of
  • Icom IC-7610 | Instruction Manual basic - Page 48
    format all SD cards with the Format function. Format, even preformatted cards for PCs or other uses. DDFormatting the SD card or USB flash drive 1. Open the SD CARD or USB FLASH DRIVE screen. MENU » SET > SD Card MENU » SET > USB Flash Drive 2. Touch "Format." (Example: SD card) Unmounting Before
  • Icom IC-7610 | Instruction Manual basic - Page 49
    be used. 3. Touch [ANT] and select "2 (ANT2)." "2 " is displayed. "2 " is displayed. LYou can recall the originally saved antenna setting (Example: ANT1), touch [ANT MR]. 4. Touch [ANT MW] for 1 second to save "2 (ANT2)" to the 10 MHz band disappears. 5. To close the ANTENNA screen after
  • Icom IC-7610 | Instruction Manual basic - Page 50
    as the type.) L"Connect Receive Antenna" is set as the default. 1. Display the ANTENNA screen. MENU » ANTENNA 2. Touch [TYPE]. Antenna type ••The TYPE SET screen is displayed. 3. Touch "RX-ANT Connectors." About the internal antenna tuner The internal automatic antenna tuner automatically matches
  • Icom IC-7610 | Instruction Manual basic - Page 51
    PTT Start" item on the TUNER screen. (p. 8-3) MENU » SET manual tuning. About an external antenna tuner The optional AH-4 antenna tuner matches the IC-7610 to a long wire antenna more than 7 m/23 ft long (3.5 MHz and above). In addition, using the optional AH-2b antenna element matches the IC-7610
  • Icom IC-7610 | Instruction Manual basic - Page 52
    tuner When you use a non-Icom external antenna tuner, be sure to turn OFF the internal antenna tuner before connecting it. Otherwise, the tuning may fail because both antenna tuners (internal and external) will simultaneously start tuning. See the antenna tuner's instruction manual for details
  • Icom IC-7610 | Instruction Manual basic - Page 53
    use the Set mode to set infrequently changed values or function settings. DDEntering the Set mode 1. Push MENU . MENU 2. Touch [SET]. 3. Touch back a level, depending on the selected item. 2 3 5. Touch the item to open the item's setting screen, or to open its next tree level. 4 LTo go back
  • Icom IC-7610 | Instruction Manual basic - Page 54
    MENU » SET > Tone Control > RX > CW MENU » SET > Tone Control > RX > RTTY MENU » SET > Tone Control > RX > PSK RX HPF/LPF (Default Sets the cut- the receive audio highpass filter or low-pass filter in 100 Hz steps in the CW, RTTY, and PSK modes. MENU » SET > Tone Control > TX > SSB TX Bass
  • Icom IC-7610 | Instruction Manual basic - Page 55
     (Default: OFF) (Default: OFF) Sets the TX delay time on the HF or 50 MHz band. LIf an external equipment's rise time is slower than that of the IC-7610, a reflected wave is produced and it may damage the IC-7610 or the external device. To prevent this, set the appropriate delay time so that
  • Icom IC-7610 | Instruction Manual basic - Page 56
    of CLEAR for the RIT and ∂TX functions. [NOTCH] Switch (SSB) [NOTCH] Switch (AM) (Default: Auto/Manual) (Default: Auto/Manual) Selects the notch function used in the SSB or AM mode. FILTER Screen MAIN/SUB Select (Default: Auto (by FILTER, PBT Operation) Selects whether or not to automatically
  • Icom IC-7610 | Instruction Manual basic - Page 57
    Default: 0) Sets the audio output level ratio of the headphone and internal speaker between -15 and +15. L/R Mix (Default: OFF) Selects to MENU » SET > Connectors > MOD Input 12 ACC MOD Level (Default: 50%) Sets the modulation input level of [ACC]. 13 USB MOD Level 14 (Default: 50%)
  • Icom IC-7610 | Instruction Manual basic - Page 58
    selected in the "USB SEND" or "USB Keying (RTTY)" item. USB Keying (RTTY) (Default: OFF) You can control transmit, receive and RTTY (FSK) from the PC, through the USB port. Selects the control port to be used for communication between the IC-7610 and PC. LYou cannot select the terminal which is
  • Icom IC-7610 | Instruction Manual basic - Page 59
    IC-7610. CI-V Transceive (Default: ON) Turns the Transceive function ON or OFF. CI-V USB/LAN→REMOTE Transceive Address (Default: 00) Sets the address used to remotely control the transceiver or receiver using type, especially when connecting a non-Icom linear amplifier. 6 ACC BAND Voltage
  • Icom IC-7610 | Instruction Manual basic - Page 60
    between the IC-7610 and the remote station. MENU » SET > Network Network Radio Name (Default: IC-7610) If you are operating the IC-7610 using the meter needle response speed to Slow, Mid or Fast. Meter Type (Normal Screen) (Default: Standard) Sets the S/RF meter type for the normal display
  • Icom IC-7610 | Instruction Manual basic - Page 61
    internal clock The IC-7610 has a If you do not use the transceiver for a SD card. 19 SD Card Info Displays the SD card capacity and the time remaining 20 for voice recording. 21 Screen Capture View Displays the selected screen capture. Firmware Update Displays the Firmware Update
  • Icom IC-7610 | Instruction Manual basic - Page 62
    or deleted. Others MENU » SET > Others > Information Version Displays the transceiver firmware's version number. MENU » SET > Others Touch Screen Calibration Touch to adjust the touch screen. LSee the Advanced Manual for details. MENU » SET > Others > Reset Partial Reset Resets operating
  • Icom IC-7610 | Instruction Manual basic - Page 63
    time stations. 15 Set the CLOCK2 function ON to display the time on the operating screen. (Default: ON) 16 1. Display the TIME SET screen. 17 MENU » SET > Time Set 18 2. Touch "CLOCK2 Function." 3. Touch ON or OFF. 19 ••ON: CLOCK2's time is displayed under the current time. 20 ••OFF
  • Icom IC-7610 | Instruction Manual basic - Page 64
    the time offset for CLOCK2 the same as for the current time. 1. Display the TIME SET screen. MENU » SET > Time Set 2. Touch "CLOCK2 UTC Offset." ••Displays the CLOCK2 UTC offset editing screen. 3. Touch [+] or [-] to set the UTC offset. DDEditing the CLOCK2 name You can edit CLOCK2's 3 character
  • Icom IC-7610 | Instruction Manual basic - Page 65
    the problem still exists, perform a Partial reset, as described to the right. If the problem SD card before an All reset. (p. 10-1) DDPartial reset 1. Open the RESET screen. 1 MENU » SET > Others > Reset 2 2. Touch "Partial Reset." 3 4 5 ••The confirmation screen is displayed. 6 3. Touch
  • Icom IC-7610 | Instruction Manual basic - Page 66
    cause of a problem, or solve it through the use of this chart, contact your nearest Icom Dealer or Service Center. PROBLEM POSSIBLE CAUSE on whichever band is selected (Main or Sub). p. 1-1 Check the external speaker cable and - repair it. Turn OFF the attenuator in the Multi-function key
  • Icom IC-7610 | Instruction Manual basic - Page 67
    MAINTENANCE 10 Troubleshooting (Continued) PROBLEM The transceiver automatically switches to transmit 3. The coaxial cable is not suitable. Use a coaxial cable whose characteristic p. 12-1 impedance is 50 Ω. "OVF" is displayed. The touch screen is not working correctly. An excessively strong
  • Icom IC-7610 | Instruction Manual basic - Page 68
    11 SPECIFICATIONS DDGeneral ••Frequency coverage (unit: MHz): Dimensions (projections not included): 340 (W) × 118 (H) × 277 (D) mm, 13.4 (W) × 4.6 (H) × 10.9 (D) in ••Weight (approximate): 8.5 kg, 18.7 Ib DDTransmitter ••Transmit output power: HF and 50 MHz bands SSB/CW/RTTY
  • Icom IC-7610 | Instruction Manual basic - Page 69
    than +10 dBm (3.2 μV) FM Less than -10 dBm (0.32 μV) (HF band: P.AMP1 ON, 50 MHz band: P.AMP2 ON) 13 ••Selectivity ( than 3.6 kHz/-60 dB More than 500 Hz/-6 dB 15 RTTY (BW=500 Hz) Less than 700 Hz/-60 dB More seconds (maximum) LAll stated specifications are typical and subject to
  • Icom IC-7610 | Instruction Manual basic - Page 70
    12 OPTIONS Options IC-PW1/IC-PW1EURO linear amplifier HF/50 MHz all band 1 kW linear amplifi eXternal SpeaKer External speaker with high and low frequency cut functions. (2 W/8 Ω) SP-34 eXternal SpeaKer External speaker with high and low frequency cut functions. (3 W/8 Ω) • AH-5NV nViS Kit Use
  • Icom IC-7610 | Instruction Manual basic - Page 71
    13 CONNECTOR INFORMATION Interface information PHONES (p. 13-3) ••6.35 mm (¼ in) (d) ELEC-KEY (p. 13-3) ••6.35 mm (¼ in) (d) USB ports (p. 13-4) ••A type MIC (p. 13-3) TUNER (p. 13-3) DC 13.8 V (p. 13-3) RX-ANT OUT (p. 13-6) ••BNC connector: 50 Ω RX-ANT IN (p. 13-6) ••BNC connector: 50 Ω REF IN
  • Icom IC-7610 | Instruction Manual basic - Page 72
    or a PC to control an external unit or the transceiver. ••ACC sockets ACC 1 8-pin 2 4 5 183 6 7 Rear panel view PIN No. NAME DESCRIPTION SPECIFICATIONS 1 RTTY Controls RTTY keying. High level: Low level: Output current: More than 2.4 V Less than 0.6 V Less than 2 mA 2 GND
  • Icom IC-7610 | Instruction Manual basic - Page 73
    PTT 3 r Squelch line output 4 NOTE: Pin 1 outputs 8 V DOC power for Icom 5 microphones. LYou can turn OFF the DC power when you use non-Icom 6 microphones in the "MIC Input DC Bias" item on the CONNECTORS screen. 7 PIN No. DESCRIPTION 8 q Microphone input w +8 V DC output (Maximum 10
  • Icom IC-7610 | Instruction Manual basic - Page 74
    card reader, USB HDD, USB flash drive, or Bluetooth® keyboard or mouse, as these are not supported by Icom Voice memory (T1 ~ T8), RTTY Memory (RT1 ~ RT8), PSK memory (PT1 ~ PT8) to be transmitted. LTo use this function, set the following items screen. MENU » SET > Connectors > SEND Relay Type
  • Icom IC-7610 | Instruction Manual basic - Page 75
    driver and driver's installation guide can be downloaded from Icom web site. USB 1 USB (1.1/2.0) type B Connect to the PC when: 1 ••Outputting the decoded FSK (RTTY download the USB driver and installation guide from the Icom website. 8 http://www.icom.co.jp/world/support/download/firm/
  • Icom IC-7610 | Instruction Manual basic - Page 76
    Function ••You cannot select the antenna or use the internal antenna tuner while the Transverter function is ON. LSet the offset frequency for the transverter operation. MENU » SET > Function > Transverter Offset ANT 1 / ANT 2 Connect a 50 Ω antenna for the HF to 50 MHz frequency band. ••Input
  • Icom IC-7610 | Instruction Manual basic - Page 77
    recommendation limits are specified as an average during 6 minutes) Normally the transmitter is not active for long periods of time. Some radio licenses will require that a timer circuit automatically cuts the transmitter after 1-2 minutes etc. Similarly some types of emission, i.e., SSB, CW, AM
  • Icom IC-7610 | Instruction Manual basic - Page 78
    screen 7-1 Memory settings 7-1 Type 7-2 Antenna tuner Connecting 2-2 External, About 7-3 External, Using 7-4 Internal, About 7-2 Internal, Using 7-3 Specifications Non-Icom linear Scope 5-1 Formatting, SD card/USB flash drive 2-1 I IC-PW1/IC-PW1EURO 2-3 3-3 L Level, Noise Blanker 4-5 Linear
  • Icom IC-7610 | Instruction Manual basic - Page 79
    4-5 Noise Reduction 4-5 Notch Auto 4-6 Filter 4-6 Function type 4-6 Manual 4-7 O Operating band, Selecting 3-3 Operating mode, Selecting 3-3 Options 12-1 Oscilloscope Waveform Color 5-3 Others (Set mode 8-10 Output power, Transmit 3-8 P Panel Front 1-1 Rear 1-3 Touch screen 1-4 Pitch
  • Icom IC-7610 | Instruction Manual basic - Page 80
    IC-7610 #13 (Europe) < Intended Country of Use > AT BE CY CZ DK EE FI FR DE GR HU IE IT LV LT LU MT NL PL PT SK SI ES SE GB IS LI NO CH BG RO TR HR A7380D-1EX Printed in Japan © 2017 Icom Inc. 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
BASIC MANUAL
i7610
HF/50 MHz TRANSCEIVER